Multi-objective optimization of the fiber-reinforced composite injection molding process using Taguchi method, RSM, and NSGA-II

Kashyap, 2015, Process parameter optimization of plastic injection molding: a review, Int. J. Plastics Technol., 19, 1, 10.1007/s12588-015-9115-2 Pei, 2002, Multi-objective optimization scheme for quality control in injection molding, Intell. Transp. Syst. J., 6, 331 Kuram, 2013, Investigating the effects of recycling number and injection parameters on the mechanical properties of glass-fibre reinforced nylon 6 using Taguchi method, Mater. Des., 49, 139, 10.1016/j.matdes.2013.02.027 Ozcelik, 2010, Influence of injection parameters and mold materials on mechanical properties of ABS in plastic injection molding, Int. Commun. Heat Mass Transf., 37, 1359, 10.1016/j.icheatmasstransfer.2010.07.001 KC, 2016, Sisal-glass fiber hybrid biocomposite: optimization of injection molding parameters using Taguchi method for reducing shrinkage, Composites A, 83, 152, 10.1016/j.compositesa.2015.10.034 Kamaruddin, 2010, Application of taguchi method in the optimization of injection moulding parameters for manufacturing products from plastic blend, Int. J. Web Eng. Technol., 2, 574, 10.7763/IJET.2010.V2.184 Oktem, 2007, Application of Taguchi optimization technique in determining plastic injection molding process parameters for a thin-shell part, Mater. Des., 28, 1271, 10.1016/j.matdes.2005.12.013 Zhang, 2016, Optimization design for turbodrill blades based on response surface method, Adv. Mech. Eng., 8, 1, 10.1177/1687814015624833 Ihesiulor, 2014, Validation of algorithms for delamination detection in composite structures using experimental data, J. Compos. Mater., 48, 969, 10.1177/0021998313480414 Shen, 2007, Optimization of injection molding process parameters using combination of artificial neural network and genetic algorithm method, J. Mater. Process. Technol., 183, 412, 10.1016/j.jmatprotec.2006.10.036 Altan, 2010, Reducing shrinkage in injection moldings via the Taguchi, ANOVA and neural network methods, Mater. Des., 31, 599, 10.1016/j.matdes.2009.06.049 Gaitonde, 2012, Surface roughness analysis in high-speed drilling of unreinforced and reinforced polyamides, J. Compos. Mater., 46, 2659, 10.1177/0021998311431640 Kurtaran, 2006, Efficient warpage optimization of thin shell plastic parts using response surface methodology and genetic algorithm, Int. J. Adv. Manuf. Technol., 27, 468, 10.1007/s00170-004-2321-2 Chen, 2016, Optimization of the plastic injection molding process using the Taguchi method, RSM, and hybrid GA-PSO, Int. J. Adv. Manuf. Technol., 83, 1 Loera, 2008, Setting the processing parameters in injection molding through multiple-criteria optimization: a case study, IEEE Trans. Syst. Man Cybern. C Appl. Rev., 38, 710, 10.1109/TSMCC.2008.923883 Peng, 2016, Multi-objective particle optimization algorithm based on sharing–learning and dynamic crowding distance, Optik – Int. J. Light Electron Opt., 127, 5013, 10.1016/j.ijleo.2016.02.045 Rao, 2009, Multi-objective optimal design of hybrid laminate composite structures using scatter search, J. Compos. Mater., 43, 2157, 10.1177/0021998309339221 Yin, 2011, A hybrid of back propagation neural network and genetic algorithm for optimization of injection molding process parameters, Mater. Des., 32, 3457, 10.1016/j.matdes.2011.01.058 Hong, 2014, Optimization of injection molding process for car fender in consideration of energy efficiency and product quality, J. Comput. Des. Eng., 1, 256 Kitayama, 2014, Multi-objective optimization of volume shrinkage and clamping force for plastic injection molding via sequential approximate optimization, Simul. Model. Pract. Theory, 48, 35, 10.1016/j.simpat.2014.07.004 Ning-Yun, 2012, Multi-objective process parameter optimization for energy saving in injection molding process, J. Zhejiang Univ. Sci. A, 13, 382, 10.1631/jzus.A1100250 Xu, 2012, Multi-objective optimization of MIMO plastic injection molding process conditions based on particle swarm optimization, Int. J. Adv. Manuf. Technol., 58, 521, 10.1007/s00170-011-3425-0 Tang, 2007, The use of Taguchi method in the design of plastic injection mould for reducing warpage, J. Mater. Process. Technol., 182, 418, 10.1016/j.jmatprotec.2006.08.025 Ozcelik, 2006, Comparison of the warpage optimization in the plastic injection molding using ANOVA, neural network model and genetic algorithm, J. Mater. Process. Technol., 171, 437, 10.1016/j.jmatprotec.2005.04.120 Chiang, 2007, Analysis of shrinkage and warpage in an injection-molded part with a thin shell feature using the response surface methodology, Int. J. Adv. Manuf. Technol., 35, 468, 10.1007/s00170-006-0739-4 Mathivanan, 2009, Sink-mark minimization in injection molding through response surface regression modeling and genetic algorithm, Int. J. Adv. Manuf. Technol., 45, 867, 10.1007/s00170-009-2021-z Tian, 2017, Multi-objective optimization of injection molding process parameters in two stages for multiple quality characteristics and energy efficiency using Taguchi method and NSGA-II, Int. J. Adv. Manuf. Technol., 1, 241, 10.1007/s00170-016-9065-7 Rong, 2016, Multi-objective optimization of laser brazing with the crimping joint using ANN and NSGA-II, Int. J. Adv. Manuf. Technol., 85, 1239, 10.1007/s00170-015-8028-8