Moment-resisting-frames under cyclic loading: Large scale tests and validation of plasticity and damage numerical models

Eurocode 3: Design of steel structures - Part 1-1: General rules and rules for buildings; EN 1993-1-1:2005. Eurocode 3: Design of steel structures – Part 1-12: Additional rules for the extension of EN 1993 up to steel grades S700; EN 1993-1-12:2007. Eurocode 3: Design of steel structures - Part 1-10: Material toughness and through-thickness properties; EN 1993-1-10:2005. EN 10025: Hot rolled products of structural steels; EN 10025:2005. Eurocode 3: Design of steel structures - Part 1-8: Design of joints; EN 1993-1-8:2005. Eurocode 8: Design of structures for earthquake resistance -Part 1: General rules, seismic actions and rules for buildings; EN 1998-1:2003. Bleck, 2009, Numerical and experimental analyses of damage behaviour of steel moment connection, Eng Fract Mech, 76, 1531, 10.1016/j.engfracmech.2009.03.004 Amiri, 2013, Finite element simulation of ultra-low cycle fatigue cracking in steel structures, J Constr Steel Res, 89, 175, 10.1016/j.jcsr.2013.07.007 Feldmann, 2011, Toughness requirements for plastic design with structural steel, Steel Constr Des Res, 4, 94, 10.1002/stco.201110013 Karlos, 2012, Ultra-Kurzzeitermüdung Geschweisster Knotenverbindungen aus Stahl, Bauingenieur, 87, 130 Feldmann, 2017, Assessing the net section resistance and ductility requirements of EN 1993-1-1 and EN 1993-1-12, Steel Constr Des Res, 10, 354, 10.1002/stco.201710036 Schaffrath S., Münstermann S., Di Y., Vayas I., Avgerinou S., Salvatore W., et al, “ Material Choice for Seismic Resistant Structures – MATCH project, Final Technical Report”, Research Programme of the Research Fund for Coal and Steel, 2018. Unpublished. FEMA. State of the Art Report on Connection Performance. FEMA-355D, Prepared by the SAC Joint Venture for the Federal Emergency Management Agency; 2000. FEMA, 2000 Kuwamura, 1998, Fracture of steel during an earthquake—state-of-the-art in Japan, Eng Struct, 20, 310, 10.1016/S0141-0296(97)00030-8 BRI, 1996 FEMA, 2000 Mazzolani F. Moment Resistant Connections of Steel Frames in Seismic Areas: Design and Reliability, E & FN Spoon ed; 2000. Eurocode 8: Design of structures for earthquake resistance - Part 3: Assessment and Retrofitting of buildings; EN 1998-3:2004. Plumier A. New idea for safe structure in seismic zone. In: Proceedings of IABSE symposium, mixed structures including new materials. 1990. p. 431_36, Brussels. Popov E, Blondet M, Stepanov L. Application of dog bones for improvement of seismic behavior of steel connections. Report no UCB/EERC 96/05. USA; 1996. Moore, 1999 Ahmady Jazany, 2017, Improved design of drilled flange (DF) moment resisting connection for seismic regions, Bull Earthq Eng Vetr MGH, Miri M, Haddad A. Seismic Behavior of a New Reduced Beam Section Connection by Drilled Holes Arrangement (RBS_DHA) on the Beam Flanges through Experimental Studies. 15Wcee; 2012. Lee SJ, Han SE, Noh SY, Shin S. Deformation Capacity of Reduced Beam Section Moment, (June); 2007. p. 1067–72. Wallin, 2011 ECCS. Recommended testing procedure for assessing the behaviour of structural steel elements under cyclic loads. Technical committee 1: structural safety and loadings, technical working group 1.3: seismic design; 1986. SAP2000, Computers & Structures Inc., Frederick, 2007, A mathematical representation of the multiaxial Bauschinger effect, Mater High Temp, 24, 1, 10.3184/096034007X207589 Chatzopoulou, 2016, Finite element analysis of UOE manufacturing process and its effect on mechanical behavior of offshore pipes, Int J Solids Struct, 83, 13, 10.1016/j.ijsolstr.2015.12.020 Ucak, 2011, Constitutive model for cyclic response of structural steels with yield plateau, J Struct Eng, 137, 195, 10.1061/(ASCE)ST.1943-541X.0000287 Ohata, 2004, Damage concept for evaluating ductile cracking of steel structure subjected to large-scale cyclic straining, Sci Technol Adv Mater, 5, 241, 10.1016/j.stam.2003.10.007 Bai, 2008, A new model of metal plasticity and fracture with pressure and Lode dependence, Int J Plast, 24, 1071, 10.1016/j.ijplas.2007.09.004