Modification of Portland Cement with Nano SiC

Cassagnabere F, Mouret M, Escadeillas G, Broillard P, Bertrand A (2010) Metakaolin, a solution for the precast industry to limit the clinker content in concrete: mechanical aspects. Constr Build Mater 24(7):1109–1118

Hranilovi M, Brajdi J, Hranilovi M (2008) (Abstract) Report on the compliance of concrete with structural design requirements. Gradevinar 60(1):13–19

Tomanović Z (2012) The stress and time dependent behaviour of soft rocks. Gradevinar 64(12):993–1007

Bahari A, Sadeghi-Nik A, Roodbari M, Mirshafiei E (2015) Effect of silicon carbide nano dispersion on the mechanical and nanostructural properties of cement. Nat Acad Sci Lett 38:361

Bahari A, Sadeghi-Nik A, Roodbari M, Taghavi K, Mirshafiei SE (2012) Synthesis and strength study of cement mortars containing SiC nano particles. Dig J Nanomater Biostruct 7:1427–1435

Gomez-Toledo C (1977) Studies on cement paste and concrete both made with low porosity cement. JTRP Technical Reports, Purdue e-Pubs

Shon I, Song H, Ko I (2011) Simultaneous synthesis and densification of a nanocrystalline(W, Ti)Si2-SiC composite from mechanically activated powders by high frequency induction heating. Mater Trans 52:2258–2261

Taha A, Hammad F (1990) Application of the hall-petch relation to microhardness measurements on Al, Cu, Al-MD 105, and Al–Cu alloys. Physica status solidi (a) 119:455–462

ASTM C150-04 (2004) Standard specification for Portland cement. ASTM International, West Conshohocken, PA

ASTM C109/C109M-02 (2002) Standard test method for compressive strength of hydraulic cement mortars (using 2-in. or [50-mm] cube specimens). ASTM International, West Conshohocken, PA

ASTM C348-02 (2002) Standard test method for flexural strength of hydraulic-cement mortars. ASTM International, West Conshohocken, PA

Hansen N (2004) Hall–Petch relation and boundary strengthening. ScriptaMaterialia 51:801–806

Mote V, Purushotham Y, Dole B (2012) Williamson–Hall analysis in estimation of lattice strain in nanometer-sized ZnO particles. J Theor Appl Phys 6:6–14

Guneyisi E, Gesogku M, Ozbay E (2011) Strength and drying shrinkage of self-compacting concretes incorporating multi-system blended mineral admixtures. Constr Build Mater 24(10):1878–1887

Presuel-Moreno F, Scully JR, Sharp SR (2010) Literature review of commercially available alloys that have potential as low-cost corrosion-resistant concrete reinforcement. Corrosion 68:1–13

Bahari A, Roodbari Shahmiri M, Mirnia N (2012) Modified homotopy perturbation method for modeling quantum dots in the quantum clusters. Int Theor Phys 51:3464–3475

Roodbari M, Bahari A, Karimi HN, Mirnia H, Hosseinzadeh R (2012) A novel nanocomposite carbon paste electrode as a sensor and ethynylferrocene as a mediator for simultaneous determination of glutathione and acetaminophen. Sens Actuators B Chem 177:70–77

Bahari A, Sadeghi-Nik A, Roodbari M, Mirnia N (2012) Investigation the Al-Fe-Cr-Ti nano composites structures with using XRD and AFM techniques. Sadhana 37:657–664

Bahari A, Robenhagen U, Morgen P, Li Z (2005) Growth of ultrathin silicon nitride on Si(111) at low temperature. Phy Rev B 72:205323–205328

Bahari A, Morgen P, Li Z (2008) Ultra-thin silicon nitride films on Si(100) studied with core level photoemission. Surf Sci 602:2315–2323

Beigi M, Berenjian J, Lotfi-Omran O, Sadeghi-Nik A, Nikbin A (2013) An experimental survey on combined effects of fibers and nanosilica on the mechanical, rheological, and durability properties of self-compacting concrete. Mater Des 50:1019–1029

Sadeghi-Nik A, Lotfi-Omran O (2013) Estimation of compressive strength of self-compacted concrete with fibers consisting nano-SiO2 using ultrasonic pulse. Constr Build Mater 44:654–662

Amiri B, Bahari A, Sadeghi-Nik A, Movahedi N (2012) Use of AFM technique to study the nano- silica effects in concrete mixture. IJST 5:2055–2063

Sadeghi-Nik A, Bahari A, Khorshidi Z, Gholipur R (2012) Effect of lanthanum oxide on the bases of cement and concrete. In: Third international conference on construction in developing countries (Advancing Civil, Architectural and Construction Engineering & Management), Bangkok, Thailand, July 4–6, pp 707–712