Modeling of burr size in drilling of aluminum silicon carbide composites using response surface methodology

Gaitonde, 2007, Methodology of Taguchi optimization for multi-objective drilling problem to minimize burr size, Int. J. Adv. Manuf. Technol, 34, 1, 10.1007/s00170-006-0571-x Dhanke, 2013, Multi response optimization of process parameters in drilling of AISI 1015 steel for exit burr using combined PCA and grey relational analysis, Int. J. Mech. Prod. Eng. Res. Dev, 3, 91 Kilickap, 2011, Optimization of drilling parameters on surface roughness in drilling of AISI 1045 using response surface methodology and genetic algorithm, Int. J. Adv. Manuf. Technol, 52, 79, 10.1007/s00170-010-2710-7 Haq, 2008, Multi response optimization of machining parameters of drilling Al/SiC metal matrix composite using grey relational analysis in the Taguchi method, Int. J. Adv. Manuf. Technol, 37, 250, 10.1007/s00170-007-0981-4 Kumar, 2013, Selection of influential factors in drilling of aluminium metal matrix composites using grey relational analysis, W. J. Eng. Sci, 1, 197 Gaitonde, 2008, Integrating Box–Behnken design with genetic algorithm to determine the optimal parametric combination for minimizing burr size in drilling of AISI 316L stainless steel, Int. J. Adv. Manuf. Technol, 37, 230, 10.1007/s00170-007-0957-4 Kilickap, 2010, Modeling and optimization of burr height in drilling of Al-7075 using Taguchi method and response surface methodology, Int. J. Adv. Manuf. Technol, 49, 911, 10.1007/s00170-009-2469-x Singh, 2014, Multi response optimization in drilling Al6063/SiC/15% metal matrix composite, Int. J. Chem. Nucl. Mater. Metal. Eng, 8, 278 Raj, 2013, Influence of drill geometry on surface roughness in drilling of Al/SiC/Gr hybrid metal matrix composites, Indian J. Sci. Technol, 6, 5002, 10.17485/ijst/2013/v6i7.21 Rajmohan, 2012, Optimization of machining parameters in drilling hybrid aluminium metal matrix composites, Transact. Nonfer. Metals Soc. China, 22, 1286, 10.1016/S1003-6326(11)61317-4 Manna, 2011, An experimental investigation on drilled hole surface during drilling of Al/SiC-MMC, Int. J. Surf. Eng. Mater. Technol, 1, 39 Taþkesen, 2013, Optimization of the drilling parameters for the cutting forces in B4C-reinforced Al-7XXX-series alloys based on the Taguchi method, Mater. Technol, 47, 169 Tsao, 2007, Taguchi analysis of drilling quality associated with core drill in drilling of composite material, Int. J. Adv. Manuf. Technol, 32, 877, 10.1007/s00170-006-0414-9 Palanikumar, 2007, Assessment of factors influencing surface roughness on the machining of Al/SiC particulate composites, Mater. Des, 28, 1584, 10.1016/j.matdes.2006.02.010 Rajmohan, 2013, Grey-fuzzy algorithm to optimise machining parameters in drilling of hybrid metal matrix composites, Compos. B Eng, 50, 297, 10.1016/j.compositesb.2013.02.030 Basavarajappa, 2008, Drilling of hybrid aluminium matrix composites, Int. J. Adv. Manuf. Technol, 35, 1244, 10.1007/s00170-006-0804-z Koklu, 2012, Influence of the process parameters and the mechanical properties of aluminum alloys on the burr height and the surface roughness in dry drilling, Mater. Technol, 46, 103 Thakre, 2015, Prediction of erosion of polyetherimide and its composites using response surface methodology, J. Tribol, 137, 11603, 10.1115/1.4028267 Goswami, 2014, Optimization in wire-cut EDM of Nimonic-80A using Taguchi's approach and utility concept, Eng. Sci. Tech. Int. J., 17, 236, 10.1016/j.jestch.2014.07.001 Das, 2016, Application of grey fuzzy logic for the optimization of CNC milling parameters for Al–4.5%Cu–TiC MMCs with multi-performance characteristics, Eng. Sci. Tech. Int. J., 19, 857, 10.1016/j.jestch.2015.12.002 Gupta, 2015, Investigation of surface roughness and MRR for turning of UD-GFRP using PCA and Taguchi method, Eng. Sci. Tech. Int. J., 18, 70, 10.1016/j.jestch.2014.09.006