Investigation of tensile strength, hardness and wear of titanium diboride reinforced AA6061 composite

Abo Zeid, 2019, Mechanical and electrochemical characteristics of solutionized AA 6061, AA6013 and AA 5086 aluminum alloys, J. Mater. Res. Technol., 8, 1870, 10.1016/j.jmrt.2018.12.014 Rao, 2018, Abrasive wear Behaviour of TiB2 Fabricated Aluminum 6061, Mater. Today Proc., 5, 268, 10.1016/j.matpr.2017.11.082 Joel, 2018, Aluminium alloy composites and its machinability studies: A review, Mater. Today Proc., 5, 13556, 10.1016/j.matpr.2018.02.351 Yao, 2017, Effects of SiC nanoparticle content on the microstructure and tensile mechanical properties of ultrafine grained AA6063-SiCnp nanocomposites fabricated by powder metallurgy, J. Mater. Sci. Technol., 33, 1023, 10.1016/j.jmst.2016.09.022 Al-reashed, 1993, Powder metallurgy route in production of aluminum alloy matrix particulate composites, J. Phys., 3, 1821 Chidambaram, 2019, Microstructure and mechanical properties of AA6061–5wt. % TiB2 in-situ metal matrix composite subjected to equal channel angular pressing, Mater. Sci. Eng. A, 759, 762, 10.1016/j.msea.2019.05.068 Diju, 2017, Production and microstructure characterization of AA6061 matrix activated carbon particulate reinforced composite by friction stir casting method, Rasayan J. Chem., 10, 784 P.B. Pawar, A.A. Utpat, “Development of aluminium based silicon carbide particulate metal matrix composite for spur gear,” Procedia Mater. Sci., vol. 6, no. Icmpc, pp. 1150–1156, 2014. Selvaganesan, 2013, Production and characterization of Al 6061- TiB2 metal matrix composites, Int. J. Res. Technol., 2, 3154 Hillary, 2020, A study on microstructural effect and mechanical behaviour of Al6061–5%SiC–TiB2 particulates reinforced hybrid metal matrix composites, J. Compos. Mater., 54, 2327, 10.1177/0021998319894666 Manikandan, 2017, Design and analysis of aluminium alloy -Tib2 and silicon carbide composite piston, Int. J. Adv. Res. Basic Eng. Sci. Technol., 3, 828 Araz, 2015, An investigation on the microstructure and wear properties of TiB2 reinforced AA2014 aluminium alloy produced by vacuum infiltration, High Temp. Mater. Process., 34, 487, 10.1515/htmp-2014-0102 M. Nazari, H. Eskandari, F. Khodabakhshi, “Production and characterization of an advanced AA6061-Graphene-TiB2 hybrid surface nanocomposite by multi-pass friction stir processing,” Surf. Coatings Technol., vol. 377, no. June, p. 124914, 2019. Baghchesara, 2014, Production and microstructural investigation of Al-nano TiB2 composite produced by powder metallurgy technique, Int. J. Nano Dimens., 5, 563 Kumar, 2020, Sliding wear performance of graphite reinforced AA6061 alloy composites for rotor drum/disk application, Mater. Today Proc., 27, 1972, 10.1016/j.matpr.2019.09.042 Jeevan, 2012, Compaction, sintering and mechanical properties of Al-SiCp composites, Int. J. Mech. Eng. Technol., 3, 565 Lijay, 2016, Microstructure and mechanical properties characterization of AA6061/TiC aluminum matrix composites synthesized by in situ reaction of silicon carbide and potassium fluotitanate, Trans. Nonferrous Met. Soc. China (English Ed.), 26, 1791, 10.1016/S1003-6326(16)64255-3 Vijaya, 2018, Tribological behavior of Al-Cu alloys and innovative Al-Cu metal matrix composite fabricated using stir-casting technique, Mater. Today Proc., 5, 885, 10.1016/j.matpr.2017.11.161 Li, 2018, Effects of asymmetric feeder on microstructure and mechanical properties of high strength Al-Zn-Mg alloy by hot extrusion, J. Alloy. Compd., 749, 293, 10.1016/j.jallcom.2018.03.188 Naga Krishna, 2014, Strengthening contributions in ultra-high strength cryorolled Al-4%Cu-3%TiB2 in situ composite, Trans. Nonferrous Met. Soc. China (English Ed., 24, 641, 10.1016/S1003-6326(14)63106-X