Investigation of tensile and flexural properties of kenaf fiber-reinforced acrylonitrile butadiene styrene composites fabricated by fused deposition modeling
Tóm tắt
Employment of natural fiber for the filament of fused deposition modeling (FDM) can be found in numerous studies from different areas. However, the presence of fiber such as kenaf in polymer filament could cause mechanical properties degradation with regard to the fiber loading owing to low compatibility between natural fiber and polymer matrix. Therefore, this study aims to study the mechanical properties of three-dimensional (3D)-printed structures of composites specimens with varying volume percentages of kenaf fiber. From the tensile and flexural testings, the findings revealed decrements in the tensile strength and modulus of kenaf fiber-reinforced ABS (KRABS) composites from 0 to 5% contents of kenaf fiber which were 23.20 to 11.48 MPa and 328.17 to 184.48 MPa, respectively. The raising amount of kenaf fiber at 5 to 10% raised the tensile strength and modulus from 11.48 to 18.59 MPa and 184.48 to 275.58 MPa, respectively. Flexural strength and modulus of KRABS composites were decreased at to 5% from 40.56 to 26.48 MPa and 113.05 to 60 MPa, respectively. With further kenaf fiber addition from 5 to 10%, the flexural strength and modulus were increased from 26.48 to 32.64 MPa and 60 to 88.46 MPa, respectively. These results were supported by the finding from the morphological analysis, where the presence of porosity and fiber pull out implied the poor interfacial bonding between kenaf fiber and ABS matrix. This study has successfully demonstrated the tensile and flexural performances of different volume percentages of KRABS composites filament for FDM through experimental research.
Tài liệu tham khảo
Ahmad F, Choi HS, Park MK (2015) A Review: Natural Fiber Composites Selection in View of Mechanical, Light Weight, and Economic Properties. Macromol Mater Eng 300(1):10–24. https://doi.org/10.1002/mame.201400089
ASTM D638-10 (2010) Standard test method for tensile properties of plastics. ASTM International, West Conshohocken
ASTM D790-10 (2010) Standard test method for flexural properties of unreinforced and reinforced plastics and electrical insulating materials. ASTM International, West Conshohocken
Blok LG, Longana ML, Yu H, Woods BKS (2018) An investigation into 3D printing of fibre reinforced thermoplastic composites. 22:176–186. https://doi.org/10.1016/j.addma.2018.04.039
Chakraborty S, Biswas MC (2020) 3D printing technology of polymer-fiber composites in textile and fashion industry: A potential roadmap of concept to consumer. Composite Struct 248(May):112562. https://doi.org/10.1016/j.compstruct.2020.112562
Gao X, Yu N, Li J (2020) Influence of printing parameters and filament quality on structure and properties of polymer composite components used in the fields of automotive. In: Structure and Properties of Additive Manufactured Polymer Components. Elsevier Inc. https://doi.org/10.1016/b978-0-12-819535-2.00010-7
Gordeev EG, Galushko AS, Ananikov VP (2018) Improvement of quality of 3D printed objects by elimination of microscopic structural defects in fused deposition modeling
Grujovic N, Zivic F, Zivkovic M, Sljivic M, Radovanovic A, Bukvic L, Mladenovic M, Sindjelic A (2017) Custom design of furniture elements by fused filament fabrication. Proc Inst Mech Eng, Part C: J Mech Eng Sci. https://doi.org/10.1177/0954406216646401
Gunti R, Ratna Prasad AV, Gupta AVSSKS (2018) Mechanical and degradation properties of natural fiber-reinforced PLA composites: Jute, sisal, and elephant grass. Polym Compos 39(4):1125–1136. https://doi.org/10.1002/pc.24041
Haryati A, Razali N, Petrů M, Taha M, Muhammad N, Ilyas RA (2021) Effect of chemically treated kenaf fibre on mechanical and thermal properties of PLA composites prepared through fused deposition modeling (FDM). Polymers 13(19). https://doi.org/10.3390/polym13193299
Ibrahim NA, Othman M, Abdan K, Hadithon A (2010) Poly (Lactic Acid) (PLA)-reinforced Kenaf Bast Fiber Composites: The Effect of Triacetin. J Reinforced Plastics Composites 29(7):1099–1111. https://doi.org/10.1177/0731684409344651
Kant S, Jawalkar C, Kumar S (2017) A Review on processing and mechanical performance of natural fiber composites. J Ind Eng Adv 2(2):1–8
Kariz M, Sernek M, Obućina M, Kuzman MK (2018) Effect of wood content in FDM filament on properties of 3D printed parts. Mater Today Commun 14(November 2017):135–140. https://doi.org/10.1016/j.mtcomm.2017.12.016
Kontarova S, Prikryl R, Melcova V, Mencik P, Horalek M, Figalla S, Plavec R, Feranc J, Sadilek J, Pospisilova A (2020) Printability, Mechanical and Thermal Properties of Poly(3-Hydroxybutyrate)-Poly(Lactic Acid)-Plasticizer Blends for Three-Dimensional (3D) Printing. Materials 13(4736):1–27
Le A, Correa D, Ueda M, Matsuzaki R, Castro M (2020) A review of 3D and 4D printing of natural fi bre biocomposites. Mater Design 194:108911. https://doi.org/10.1016/j.matdes.2020.108911
Lee C, Sapuan S, Hassan M (2017) Mechanical and thermal properties of kenaf fiber reinforced polypropylene/magnesium hydroxide composites. J Eng Fibers Fabrics 12(2):50–58
MacDonald E, Wicker R (2016) Multiprocess 3D printing for increasing component functionality. Science 353(6307). https://doi.org/10.1126/science.aaf2093
Mazzanti V, Malagutti L, Mollica F (2019) FDM 3D printing of polymers containing natural fillers: a review of their mechanical properties. Polymers 11(7). https://doi.org/10.3390/polym11071094
Mohammad NB, Arsad A (2013) Mechanical, thermal and morphological study of kenaf fiber reinforced rPET/ABS composites. Malaysian Polymer J 8(1):8–13
Mohan N, Senthil P, Vinodh S, Jayanth N (2017) A review on composite materials and process parameters optimisation for the fused deposition modelling process. Virtual Phys Prototyping 12(1):47–59. https://doi.org/10.1080/17452759.2016.1274490
Montalvo Navarrete JI, Hidalgo-Salazar MA, Escobar Nunez E, Rojas Arciniegas AJ (2018) Thermal and mechanical behavior of biocomposites using additive manufacturing. Int J Interactive Design Manufact 12(2):449. https://doi.org/10.1007/s12008-017-0411-2
Moradi M, Aminzadeh A, Rahmatabadi D, Hakimi A (2021) Experimental investigation on mechanical characterization of 3D printed PLA produced by fused deposition modeling (FDM). Mater Res Express 8(3). https://doi.org/10.1088/2053-1591/abe8f3
Mustafa Z, Nawi TMI, Fadzullah SHSM, Shamsudin Z, Malingam SD, Ratanawilai T (2021) Fatigue characteristic and Weibull analysis of sustainable rubberwood flour/recycled polypropylene composites. Int J Automot Mech Eng 18(4):9179–9187. https://doi.org/10.15282/IJAME.18.4.2021.03.0706
Noor Azammi AM, Sapuan SM, Ishak MR, Sultan MTH (2018) Mechanical and thermal properties of kenaf reinforced thermoplastic polyurethane (TPU)-natural rubber (NR) composites. Fibers Polymers 19(2):446–451. https://doi.org/10.1007/s12221-018-7737-7
Nur-a-tomal S, Pahlevani F, Sahajwalla V (2020) Direct transformation of waste children ’ s toys to high quality products using 3D printing: a waste-to-wealth and sustainable approach. J Clean Prod 267:122188. https://doi.org/10.1016/j.jclepro.2020.122188
Parandoush P, Lin D (2017) A review on additive manufacturing of polymer-fiber composites. Composite Struct 182:36–53. https://doi.org/10.1016/j.compstruct.2017.08.088
Pu NASM, Haq RHA, Noh HM, Abdullah HZ, Idris MI, Lee TC (2020) Review on the fabrication of fused deposition modelling ( FDM ) composite filament for biomedical applications. Materials Today: Proceedings, June, pp 1–6. https://doi.org/10.1016/j.matpr.2020.05.535
Ramesh M (2016) Kenaf (Hibiscus cannabinus L.) fibre based bio-materials: A review on processing and properties. Progress Mater Sci 78–79:1–92. https://doi.org/10.1016/j.pmatsci.2015.11.001
Ramesh M, Nijanthan S (2016) Mechanical property analysis of kenaf–glass fibre reinforced polymer composites using finite element analysis. Bull Mater Sci 39(1):147–157
Russo P, Simeoli G, Vitiello L, Filippone G (2019) Bio-polyamide 11 hybrid composites reinforced with basalt/flax interwoven fibers: a tough green composite for semi-structural applications, pp 1–11. https://doi.org/10.3390/fib7050041
Salleh F, Hassan A, Yahya R, Azzahari AD (2014) Composites: Part B Effects of extrusion temperature on the rheological , dynamic mechanical and tensile properties of kenaf fiber / HDPE composites. Composites Part B 58:259–266. https://doi.org/10.1016/j.compositesb.2013.10.068
Singh R, Singh S, Mankotia K, Torres J, Cole M, Owji A, Demastry Z, Gordon AP (2016) Development of ABS based wire as feedstock filament of FDM for industrial applications. Rapid Prototyping J 22(2). https://doi.org/10.1108/RPJ-07-2014-0086
Svoykin F, Bazarov A, Gasimov G, Alexandrov V, Bacherikov I (2020) Elements of bases of mechanics of wood-polymer composites. IOP Conf Ser: Earth Environ Sci 574(1). https://doi.org/10.1088/1755-1315/574/1/012077
Taufiq M, Mansor M, Mustafa Z (2018) Characterisation of wood plastic composite manufactured from kenaf fibre reinforced recycled-unused plastic blend. Composite Struct 189:510–515. https://doi.org/10.1016/j.compstruct.2018.01.090
Torrado AR, Shemelya CM, English JD, Lin Y, Wicker RB, Roberson DA (2015) Characterizing the effect of additives to ABS on the mechanical property anisotropy of specimens fabricated by material extrusion 3D printing. Addit Manuf. https://doi.org/10.1016/j.addma.2015.02.001
Turner BN, Gold SA (2015) A review of melt extrusion additive manufacturing processes: II. Materials, dimensional accuracy, and surface roughness. Rapid Prototyping J 21(3):250–261. https://doi.org/10.1108/RPJ-02-2013-0017
Turner BN, Strong R, Gold SA (2014) A review of melt extrusion additive manufacturing processes: I. Process design and modeling. Rapid Prototyping J 20(3):192–204. https://doi.org/10.1108/RPJ-01-2013-0012
Wang P, Zou B, Ding S, Huang C, Shi Z (2020) Preparation of short CF / GF reinforced PEEK composite filaments and their comprehensive properties evaluation for FDM-3D printing. Composites Part B 198(January):108175. https://doi.org/10.1016/j.compositesb.2020.108175
Wang X, Zhao L, Ying J, Fuh H, Lee HP (2019) Effect of porosity on mechanical properties of 3D printed polymers : experiments and micromechanical modeling based on X-ray computed tomography analysis. https://doi.org/10.3390/polym11071154
Wong KV, Hernandez A (2012) A review of additive manufacturing. ISRN Mech Eng. https://doi.org/10.5402/2012/208760
Yahaya R, Sapuan SM, Jawaid M, Leman Z, Zainudin ES (2018) Review of kenaf reinforced hybrid biocomposites: potential for defence applications, pp 226–240. https://doi.org/10.2174/1573411013666171113150225
Zhang W, Wu AS, Sun J, Quan Z, Gu B, Sun B, Cotton C, Heider D, Chou T (2017) Characterization of residual stress and deformation in additively manufactured ABS polymer and composite specimens. Composites Sci Technol 150:102–110. https://doi.org/10.1016/j.compscitech.2017.07.017