Insight into deformation allocation in the multi-pass roll forming of a double-walled brazed tube

Zhang WD, Zhao GQ, Fu QJ (2019) Optimization of roll forming process for high-strength V channel steels. Int J Adv Manuf Tech 105(2):2469–2480

Moneke M, Groche P (2021) Control of residual stresses in roll forming through targeted adaptation of the roll gap. J Mater Process Technol 294(3):117129. https://doi.org/10.1016/j.jmatprotec.2021.117129

Paralikas J, Salonitis K, Chryssolouris G (2010) Optimization of roll forming process parameters—a semi-empirical approach. Int J Adv Manuf Tech 47(9/12):1041–1052

Liu XL, Cao JG, Chai XT et al (2017) Investigation of forming parameters on springback for ultra high strength steel considering Young’s modulus variation in cold roll forming. J Manuf Process 29:289–297

Liu XL, Cao JG, Chai XT et al (2018) Experimental and numerical prediction of the local thickness reduction defect of complex cross-sectional steel in cold roll forming. Int J Adv Manuf Tech 95:1837–1848

Su CJ, Liu JZ, Zhao ZX et al (2020) Research on roll forming process and springback based on five-boundary condition forming angle distribution function. J Mech Sci Technol 34(9/12):5193–5204

Safdarian R, Naeini HM (2015) The effects of forming parameters on the cold roll forming of channel section. Thin-Walled Struct 92:130–136

Poursafar A, Saberi S, Tarkesh R et al (2022) Experimental and mathematical analysis on spring-back and bowing defects in cold roll forming process. Int J Interact Des Manuf 16(2):531–543

Yaser T, Hassan MN, Roohollah AT et al (2018) A strategy to reduce the twist defect in roll-formed asymmetrical-channel sections. Thin-Walled Struct 130:395–404

Sheu JJ, Yu CH, Wang JK (2017) Die designs of cold roll forming process for car bumper using advanced high strength steel. Procedia Eng 207:1308–1313

Fan LF, Yan JX, Gao Y et al (2016) Research on deformation characteristics of JCOE forming in large diameter welding pipe. Adv Manuf 4(3):268–277

Luo JT, Xue YH, Chen K et al (2017) Integrated simulation and experimental test of the residual stress field for large-sized straight welded pipe processed with JCOE technology. Int J Steel Struct 17(1):265–272

Ren Q, Zou TX, Li DY et al (2015) Numerical study on the X80 UOE pipe forming process. J Mater Process Technol 215:264–277

Zou TX, Wu GH, Li DY et al (2015) A numerical method for predicting O-forming gap in UOE pipe manufacturing. Int J Mech Sci 98:39–58

Zou TX, Li DY, Wu GH et al (2016) Yield strength development from high strength steel plate to UOE pipe. Mater Design 89:1107–1122

Yu JX, Han MX, Yu Y et al (2021) The research on pipe structural behavior of 3D UOE manufacturing process. Thin-Walled Struct 158:107168. https://doi.org/10.1016/j.tws.2020.107168

Chen WY, Jiang JM, Li DY et al (2019) Flower pattern and roll positioning design for the cage roll forming process of ERW pipes. J Mater Process Technol 264:295–312

Cheng JJ, Cao JG, Zhao JW et al (2020) The flower pattern and rolls design for ERW pipes with the different specification in the flexible roll forming process. Thin-Walled Struct 154:106809. https://doi.org/10.1016/j.tws.2020.106809

Qiu LM, Zhang SY, Wang ZL et al (2019) A robust optimization design method for sheet metal roll forming and its application in roll forming circular cross-section pipe. Int J Adv Manuf Tech 103(11):2903–2916

Mahendra K, Hardik K (2015) Geometric specification of bevel wrapping of double walled tubes, prediction of failure from material properties. Int J Res Eng Tech 4(7):1–6