Impact of compression and bending behavior on fused deposition modeling of 3D printed components

Gebhardt, 2018 Campbell, 2013, Additive manufacturing as a disruptive technology: Implications of three-dimensional printing, Technology & Innovation, 15, 67, 10.3727/194982413X13608676060655 Gu, 2016, Materials creation adds new dimensions to 3D printing, Science Bulletin, 61, 1718, 10.1007/s11434-016-1191-y Dudek, 2013, FDM 3D printing technology in manufacturing composite elements, Archives of metallurgy and materials, 58, 1415, 10.2478/amm-2013-0186 Lanzotti, 2015, The impact of process parameters on mechanical properties of parts fabricated in PLA with an open-source 3-D printer, Rapid Prototyping Journal, 10.1108/RPJ-09-2014-0135 Idris, 2008, Evaluation of ABS patterns produced from FDM for the investment casting process, 3 Jiang, 2013, Rubber-toughened PLA blends with low thermal expansion, Journal of Applied Polymer Science, 128, 3993, 10.1002/app.38642 Bergström, 2016, An overview of mechanical properties and material modelling of polylactide (PLA) for medical applications, Annals of biomedical engineering, 44, 330, 10.1007/s10439-015-1455-8 Liu, 2009, Enzyme-catalyzed degradation of poly (l-lactide)/poly (ɛ-caprolactone) diblock, triblock, and four-armed copolymers, Polymer degradation and stability, 94, 227, 10.1016/j.polymdegradstab.2008.10.023 Ang, 2006, Investigation of the mechanical properties and porosity relationships in fused deposition modelling-fabricated porous structures, Rapid Prototyping Journal Sood, 2010, Parametric appraisal of mechanical property of fused deposition modelling processed parts, Materials & Design, 31, 287, 10.1016/j.matdes.2009.06.016 Panda, 2009, Optimization of fused deposition modelling (FDM) process parameters using bacterial foraging technique, Intelligent information management, 1, 89, 10.4236/iim.2009.12014 Naveed, 2021, Investigate the effects of process parameters on material properties and microstructural changes of 3D-printed specimens using fused deposition modelling (FDM), Materials Technology, 36, 317, 10.1080/10667857.2020.1758475 Ning, 2017, Additive manufacturing of carbon fiber-reinforced plastic composites using fused deposition modelling: Effects of process parameters on tensile properties, Journal of composite materials, 51, 451, 10.1177/0021998316646169 D20 Committee. (2010). Test method for tensile properties of plastics.ASTM International. Abouzaid, 2018, Printability of co-polyester using fused deposition modelling and related mechanical performance, European Polymer Journal, 108, 262, 10.1016/j.eurpolymj.2018.08.034 Ahn, 2002, Anisotropic material properties of fused deposition modelling ABS, Rapid prototyping Journal., 10.1108/13552540210441166 Aliheidari, 2017, Fracture resistance measurement of fused deposition modelling 3D printed polymers, Polymer Testing, 60, 94, 10.1016/j.polymertesting.2017.03.016 Qattawi, 2017, Experimental optimization of fused deposition modelling processing parameters: a design-for-manufacturing approach, Procedia Manufacturing, 10, 791, 10.1016/j.promfg.2017.07.079 Thomas, 2014, Costs and cost effectiveness of additive manufacturing, NIST special publication, 1176, 12 Galantucci, 2009, Experimental study aiming to enhance the surface finish of fused deposition modeled parts, CIRP Ann. - Manuf. Technol., 58, 189, 10.1016/j.cirp.2009.03.071 Galantucci, 2010, Quantitative analysis of a chemical treatment to reduce the roughness of parts fabricated using fused deposition modelling, CIRP Ann. - Manuf. Technol., 59, 247, 10.1016/j.cirp.2010.03.074 Jayanth, 2018, Effect of chemical treatment on tensile strength and surface roughness of 3D-printed ABS using the FDM process, Virtual and Physical Prototyping, 13, 155, 10.1080/17452759.2018.1449565 Tiwary, 2015, Studying the effect of chemical treatment and fused deposition modelling process parameters on surface roughness to make acrylonitrile butadiene styrene patterns for the investment casting process, Int. J. Rapid Manuf., 5, 276, 10.1504/IJRAPIDM.2015.074807 Pandey, 2003, Improvement of surface finish by staircase machining in fused deposition modelling, J. Mater. Process. Technol., 132, 323, 10.1016/S0924-0136(02)00953-6 Kerbrat, 2011, A new DFM approach to combine machining and additive manufacturing, Comput. Ind., 62, 684, 10.1016/j.compind.2011.04.003 Rodríguez, 2001, Mechanical behavior of acrylonitrile butadiene styrene (ABS) fused deposition materials. The experimental investigation, Rapid Prototyp. J., 7, 148, 10.1108/13552540110395547 Bembenek, 2022, Research on the Influence of Processing Parameters on the Specific Tensile Strength of FDM Additive Manufactured PET-G and PLA Materials, Polymers, 14, 2446, 10.3390/polym14122446 Maurya, 2022, Investigation of different parameters of cube printed using PLA by FDM 3D printer, Materials Today: Proceedings, 64, 1217 Pandzic, 2019, October). Influence of material colour on mechanical properties of PLA material in FDM technology, 21 Popescu, 2018, FDM process parameters influence over the mechanical properties of polymer specimens: A review, Polymer Testing, 69, 157, 10.1016/j.polymertesting.2018.05.020 Rao, 2019, Effect of fused deposition modelling (FDM) process parameters on tensile strength of carbon fibre PLA, Materials Today: Proceedings, 18, 2012 A. Pandzic, D. Hodzic, I. Hajro, P. Tasic, (2020, January). Strength Properties of PLA Material Obtained by Different Models of FDM 3D Printer. InProceedings of the 31st DAAAM International Symposium on Intelligent Manufacturing and Automation, Mostar, ISSN(pp. 1726-9679). L. Bergonzi, M. Vettori, L. Stefanini, L. D’Alcamo, (2021, February). Different infill geometry influence on mechanical properties of FDM produced PLA. InIOP Conference Series: Materials Science and Engineering(Vol. 1038, No. 1, p. 012071). IOP Publishing. Chalgham, 2021, Mechanical properties of FDM printed PLA parts before and after thermal treatment, Polymers, 13, 1239, 10.3390/polym13081239