Identification of damage mechanism and validation of a fracture model based on mesoscale approach in spalling of titanium alloy

Arrieta, 2001, The role of thermal activation on dynamic stress-induced inelasticity and damage in Ti–6Al–4V, Mechanics of Materials, 33, 573, 10.1016/S0167-6636(01)00079-5 Boidin, 2003, Validation of a fracture model based on mesoscale approach for spalling of hard steel and aluminium alloy, Journal de Physique IV, 110, 550 Cagnoux, J., 1985. Déformation et ruine d’un verre pyrex soumis à un choc intense: étude expérimentale et modélisation du comportement. Ph.D. Thesis of Poitiers University. Chevrier, 1997, Discussion of fracture criteria in spall mechanics, Engineering Transaction, 45, 47 Chevrier, 1999, Spall fracture: mechanical and microstructural aspects, Engineering Fracture Mechanics, 63, 273, 10.1016/S0013-7944(99)00022-3 Curran, 1987, Dynamic failure of solids, vol. 5 Dremin, A.N., Molodets, A.M., 1985. On the spall strength of metals. In: Proceedings of the International Symposium on Intense Dynamic Loading and its Effects. Beijing: Pergamon Press, p. 13. Follansbee, 1989, An analysis of the low temperature, low- and high-strain rate deformation of Ti–6Al–4V, Metallurgical Transactions, 20A, 863, 10.1007/BF02651653 Gilman, 1960, Direct measurements of surface energies of crystals, Journal of Applied Physics, 31, 2208, 10.1063/1.1735524 Grady, 1988, The spall strength of condensed matter, Journal of the Mechanics and Physics of Solids, 36, 353, 10.1016/0022-5096(88)90015-4 Hanim, 1999, Numerical study of spalling in an aluminium alloy 7020-T6, International Journal of Impact Engineering, 22, 649, 10.1016/S0734-743X(99)00023-8 Klepaczko, J.R., 1988. A general approach to rate sensitivity and constitutive modelling of BCC metals. In: Effects of fast transient loadings. Rotterdam, pp. 3–35. Klepaczko, 1990, Dynamic crack initiation, some experimental methods and modelling, 428 Klepaczko, 2003, A meso-model of spalling with thermal coupling for hard metallic materials, Engineering Fracture Mechanics, 70, 2543, 10.1016/S0013-7944(03)00081-X Marchand, 1988, An experimental study of the formation process of adiabatic shear bands in a structural steel, Journal of the Mechanics and Physics of Solids, 36, 251, 10.1016/0022-5096(88)90012-9 Me-Bar, 1987, Spall studies on Ti–6Al–4V, Materials Science and Engineering, 85, 77, 10.1016/0025-5416(87)90469-1 Mescheryakov, 1999, Spall strength and phase transformation in titanium alloys in impact loading, The Physics of Metals and Metallography, 87, 443 Orowan, 1948, Fracture and strength of solids, Reports on Progress in Physics, 12, 185, 10.1088/0034-4885/12/1/309 Seo, 2005, Constitutive equation for Ti–6Al–4V at high temperature measured using the SHPB technique, International Journal of Impact Engineering, 31, 735, 10.1016/j.ijimpeng.2004.04.010 Tuler, 1968, A criterion for the time dependence of dynamic fracture, International Journal of Fracture, 26, 322, 10.1007/BF00962964 Wright, 1992, A model for fully formed shear bands, Journal of the Mechanics and Physics of Solids, 40, 1217, 10.1016/0022-5096(92)90013-R Wulf, 1979, High-strain rate compression of titanium and some titanium alloys, International Journal of Mechanical Sciences, 21, 713, 10.1016/0020-7403(79)90051-1 Zhurkov, 1965, Kinetic concept of the strength of solids, International Journal of Fracture, 1, 311, 10.1007/BF03545562