Genetic equation for the prediction of tool–chip contact length in orthogonal cutting

Abuladze, N.G., 1962. Character and the length of tool–chip contact (in Russian). In: Proceedings Machinability of Heat-resistant and Titanium Alloys, Kuibyshev 68–78. Bahi, 2011, A new friction law for sticking and sliding contacts in machining, Int. J. Tribol., 44, 764, 10.1016/j.triboint.2011.01.007 Bhattacharyya, A., 1963. On the friction forces in metal cutting. In: Proceedings of the 6th Int. Machine Tool Des. and Res. Conf. 491–505. Brezocnik, 2004, Prediction of surface roughness with genetic programming, J. Mater. Process. Technol., 157-158, 28, 10.1016/j.jmatprotec.2004.09.004 Devillez, 2004, Cutting tool crater wear measurement with white light interferometry, Wear, 256, 56, 10.1016/S0043-1648(03)00384-3 Dimopoulos, 2001, Investigating the use of genetic programming for a classic one-machine scheduling problem, Adv. Appl. Eng. Software, 32, 489, 10.1016/S0965-9978(00)00109-5 Flom, 1984, High speed machining of metals, Annu. Rev. Mater. Sci., 14, 231, 10.1146/annurev.ms.14.080184.001311 Friedman, 1970, Investigation of the tool–chip contact length in metal cutting, Int. J. Mach. Tool Des. and Res., 10, 401, 10.1016/0020-7357(70)90001-6 Hastings, 1980, A machining theory for predicting chip geometry, cutting forces, etc. from work material properties and cutting conditions, Proc. R. Soc. London, Ser. A, 371, 569, 10.1098/rspa.1980.0097 Iqbal, 2007, Characterization of the machining of AISI 045 steel over a wide range of cutting speeds—Part 1: investigation of contact phenomena, Proc. IMech. Part B: J. Eng. Manuf., 221, 909, 10.1243/09544054JEM796 Iqbal, 2008, Contact length prediction: mathematical models and effect of friction schemes on FEM simulation for conventional to HSM of AISI 045 steel, Int. J. Mach. Mach. Mater., 3, 18 Kato, 1972, Stress distribution at the interface between tool and chip in machining, Trans. ASME J. Eng. Indus., 94, 683, 10.1115/1.3428229 Klushin, 1958 Koza, 1992 Lee, 1951, The theory of plasticity applied to a problem of machining, ASME Trans. J. Appl. Mech., 18, 405, 10.1115/1.4010357 Marinov, V., 1999. The tool chip contact length on orthogonal metal cutting. 5th Int. Conf. Adv. Eng. and Tech. AMTECH 1999, Plovdiv, Bulgaria 149–155. Metenidis, 2004, A novel genetic programming approach to nonlinear system modeling: application to the DAMADICS benchmark problem, Eng. Appl. Artif. Intell., 17, 363, 10.1016/j.engappai.2004.04.009 Milfelner, 2005, Genetic equation for the cutting force in ball- end milling, J. Mater. Process. Tech., 164–165, 1554, 10.1016/j.jmatprotec.2005.02.147 Oxley, 1989 Poletika, 1969 Ramalingman, S., Desai, P.V., 1980. Tool–chip contact length in orthogonal machining. ASME Paper 80-WA/Prod-23. Rozenberg, 1990 Sadik, 1993, The role of tool–chip contact length in metal cutting, J. Mater. Process Tech., 37, 613, 10.1016/0924-0136(93)90122-M Settea, 2001, Genetic programming: principles and applications, Eng. Appl. Artif. Intell., 14, 727, 10.1016/S0952-1976(02)00013-1 Sutter, 2005, Chip geometries during high speed machining for orthogonal cutting conditions, Int. J. Mach. Tools Manuf., 45, 719, 10.1016/j.ijmachtools.2004.09.018 Toropov, 2003, Prediction of tool–chip contact length using a new slip-line solution for orthogonal cutting, Int. J. Mach. Tools Manuf., 43, 1209, 10.1016/S0890-6955(03)00155-X Zorev, 1963, Interrelationship between shear process occurring along the tool face and on the shear plane in metal cutting, Int. Res. Prod. Eng. ASME, 42