Formation of Layer WC-(Co,Ni,Al) Structure on the Cutting Plate Surface of WC-7(W,Ti)C-10Co Cemented Carbide in the Contact Area with Ni3Al Melt
Tóm tắt
It reported that a new type of the structure was found on the cutting plate surface of the WC-7(W,Ti)C-10Co cemented carbide of T5K10 brand after contact with the Ni3Al melt at 1530°C in a vacuum, which includes external WC-(Co,Ni,Al) and intermediate WC-(W,Ti)C-(Co,Ni,Al) layers with varying chemical and phase composition by thickness. The maximum content and dimensions on the Co-based phase are characteristic of the structure on the boundary of the outer and transition layers, which by 1.7 and 2 times, respectively, exceed the similar indicators in the basic structure of this sample. The formation of such a structure occurs by the output of W, C and the Co-based phase from the volume on the surface of the plate and the subsequent absorption of it by N and Al from the Ni3Al melt. It is shown that in the formed layer structure on the plate surface there is a residual microporosity but less than that in the basic structure outside the surface layer, which also decreased in comparison with the level of microporosity in the structure of the initial plate.
Tài liệu tham khảo
Serdyuk, Yu.D., Semizhon, O.A., Prokopiv, N.M., Petasyuk, G.A., Kharchenko, O.V., and Omel’chuk, T.V., The influence of thermal compression treatment parameters on quality characteristics and wear mechanisms of T5K10 carbide inserts in rough turning, J. Superhard Mater., 2011, vol. 33, no. 2, pp. 120–128.
Prokopiv, M.M., A new phenomenon in the structure formation of T5K10 hard alloy, J. Superhard Mater., 2018, vol. 40, no. 1, pp. 73–74.
Lisovsky, A.F., Some problems on technical use of the phenomenon of metal melts imbibition of sintered composites, Powder Metallurgy Intern., 1989, vol. 21, no. 6, pp. 7–10.
Lisovsky, A.F., Gracheva, T.E., and Kulakovsky, V.N., Composition and properties of (Ti,W)C-WC-Co sintered carbides alloyed by MMT-process, Int. J. Refract. Met. Hard Mater., 1995, vol. 13, no. 6, pp. 379–383.
Liu, C.T. and Pope, D.P., Ni 3 Al and Its Alloys, in: J.H. Westbrook, R.L. Fleischer, Eds., Intermetallic Compounds, New York: Wiley, 2000, pp. 17–47.
Suryanarayana, C., Mechanical alloying and milling, Prog. Mater Sci., 2001, vol. 46, nos. 1–2, pp. 1–184.
Tumanov, A.V., Gostev, Y.V., Panov, V.S., and Kots, Y.F., Wetting of TiC-WC system carbides with molten Ni3Al, Powder Metall. Met. Ceram., 1986, vol. 25, no. 5, pp. 428–430.
Aoki, A. and Izumi, O. Improvement in room temperature ductility of the L12 type intermetallic compound Ni3Al by boron addition, J. Jpn. Inst. Met., 1979, vol. 43, pp. 1190–1194.
Liu, C.T., White, C.L., and Horton J.A., Effect of boron on grain-boundaries in Ni3Al, Acta Metall., 1985, vol. 33, no. 2, pp. 213–219.
Yeh, C.L. and Sung, W.Y., Combustion synthesis of Ni3Al by SHS with boron additions, J. Alloys Compd., 2005, vol. 390, nos. 1–2, pp. 74–81.
Ohiai, S., Oya, Y., and Suzuki, T., Alloying behaviour of Ni3Al, Ni3Ga and Ni3G, Acta Metall., 1984, vol. 32, no. 2, pp. 289–298.
Tret’iakov, Y.I., Osnovy metallovedeniya i tekhnologii proizvodstva spechennykh tverdykh splavov (Fundamentals of Metallurgical Science and the Production Technology of the Baked Firm Alloys), Moscow: Metallurgiia Publ., 1976.
Chaporova, I.N. and Cherniavskii, K.S., Struktura spechennykh tverdykh splavov (Structure of Sintered Hard Alloys), Moscow: Metallurgiia Publ., 1975.
Panov, V.S., Chuvilin, A.M., and Fal’kovskii V.A., Tekhnologiya i svoistva spechennykh tverdykh splavov i izdelii iz nikh (Technology and Properties of Sintered Hard Alloys and Their Products), Moscow: MISIS, 2001.
Naidich, Y.V., Kontaktnye yavleniya v metallicheskikh rasplavakh (Contact Phenomena in Metal Melts), Kiev: Naukova Dumka, 1972.
Andersson, G. and Jansson, B., The solubility of cubic carbide formers in liquid cobalt, Proc.15th Int. Plansee Seminar 2001, Kneringer, G., Rödhammer, P., and Wilhartitz, P., Eds., Plansee Halding AG, Reutte, Austria, 2001, vol. 2, pp. 662–676.