Fatigue resistance and retentive force of cast clasps treated by shot peening

Mahmoud, 2005, Deflection fatigue of Ti–6Al–7Nb, Co–Cr, and gold alloy cast clasps, J Prosthet Dent, 93, 183, 10.1016/j.prosdent.2004.11.011 Wagner, 2000, Clinical evaluation of removable partial dentures 10 years after insertion: success rates, hygienic problems, and technical failures, Clin Oral Invest, 4, 74, 10.1007/s007840050119 Yeung, 2002, Usage and status of cobalt–chromium removable partial dentures 5–6 years after placement, J Oral Rehabil, 29, 127, 10.1046/j.1365-2842.2002.00846.x Sandu, 2007, Finite element stress analysis and fatigue behavior of cast circumferential clasps, J Prosthet Dent, 97, 39, 10.1016/j.prosdent.2006.11.003 Mahmoud, 2007, Prediction of permanent deformation in cast clasps for denture prostheses using a validated nonlinear finite element model, Dent Mater, 23, 317, 10.1016/j.dental.2005.10.012 Mahmoud, 2007, Pre-overloading to extend fatigue life of cast clasps, J Dent Res, 86, 868, 10.1177/154405910708600912 Sandu, 2010, Stress distribution in retentive arms of combination clasps used on premolars, J Appl Biomater Biomech, 8, 76 Wagner, 1999, Mechanical surface treatments on titanium, aluminum and magnesium alloys, Mater Sci Eng A, 263, 210, 10.1016/S0921-5093(98)01168-X Kostilnik, 1994, Shot peening, 126 König, 2003, Life enhancement of aero engine components by shot peening: opportunities and risks, 1 Hultmann, 2003, The application of mechanical surface treatment in the passenger car industry, 3 2004, Shot peening, 1 Gao, 2006, Influence of shot peening on tension–tension fatigue property of two high strength Ti alloys, Surf Eng, 22, 299, 10.1179/174329406X122865 Croccolo, 2002, Fatigue strength of shot-peened nitrided steel: optimization of process parameters by means of design of the experiment, Fatigue Fract Eng Mater Struct, 25, 695, 10.1046/j.1460-2695.2002.00533.x Ito, 2010, Analysis of pneumatic fine particle peening process by using a high-speed-camera, Int J Mod Phys B, 24, 3047, 10.1142/S0217979210066069 Gil, 2007, The effect of shot blasting and heat treatment on the fatigue behavior of titanium for dental implant applications, Dent Mater, 23, 486, 10.1016/j.dental.2006.03.003 Gil, 2002, Fracture and fatigue behavior of shot-blasted titanium dental implants, Implant Dent, 11, 28, 10.1097/00008505-200201000-00011 Aparicio, 2003, Corrosion behaviour of commercially pure titanium shot blasted with different materials and sizes of shot particles for dental implant applications, Biomaterials, 24, 263, 10.1016/S0142-9612(02)00314-9 Hayashi, 2010, Effect of shot-peened surface modification with minute particles on the fatigue strengths of cast titanium and cobalt–chromium Alloy, Tsurumi Univ Dent J, 36, 41 Shimpo, 2008, Effect of arm design and chemical polishing on retentive force of cast titanium alloy clasps, J Prosthodont, 17, 300, 10.1111/j.1532-849X.2007.00289.x Muraishi, 2010, Retentive forces and fitting accuracy of repaired akers clasps using laser welding, Tsurumi Univ Dent J, 36, 53 Kanki, 1993, A study on the fitness test for cast clasp, Tsurumi Univ Dent J, 19, 211 Prevey, 1986, X-ray diffraction residual stress techniques, 380 Pineault, 2002, X-Ray diffraction residual stress measurement in failure analysis, 484 Lund, 2002, Fatigue fracture appearances, 627 Nakamura, 2008 Todaka, 2004, Comparison of nanocrystalline surface layer in steels formed by air blast and ultrasonic shot peening, Mater Trans, 45, 376, 10.2320/matertrans.45.376 Iida, 1986, Variation of surface residual stress induced by shot peening, J Jpn Soc Precis Eng, 52, 535, 10.2493/jjspe.52.535 2004, Effect of shot peening, 37 Vallittu, 1995, Deflection fatigue of cobalt–chromium, titanium, and gold alloy cast denture clasp, J Prosthet Dent, 74, 412, 10.1016/S0022-3913(05)80384-1 Soma, 1998, Clinical application of Ti–6Al–7Nb Alloy “T-Alloy Tough”, QDT, 23, 1210 Rodrigues, 2012, Effect of different investments and mold temperatures on titanium mechanical properties, J Prosthodont Res, 56, 58, 10.1016/j.jpor.2011.01.002 Mellali, 1997, Alumina grit blasting parameters for surface preparation in the plasma spraying operation, J Therm Spray Technol, 6, 217, 10.1007/s11666-997-0016-6 Asami, 1994, Effect of shot-peening on suppression of scatter of fatigue strength in Ti–6Al–7Nb alloy, J Soc Mater Sci, 43, 12, 10.2472/jsms.43.12