Fabrication of functionally graded material of 304L stainless steel and Inconel625 by twin-wire plasma arc additive manufacturing

Loh, 2018, An overview of functionally graded additive manufacturing, Addit Manuf, 23, 34 Yan, 2020, Additive manufacturing of functionally graded metallic materials using laser metal deposition, Addit Manuf, 31 Tammas-Williams, 2017, Design for additive manufacturing with site-specific properties in metals and alloys, Scripta Mater, 135, 105, 10.1016/j.scriptamat.2016.10.030 Zhang, 2019, Additive manufacturing of functionally graded materials: a review, Mater Sci Eng, A, 764, 10.1016/j.msea.2019.138209 Hofmann, 2014, Developing gradient metal alloys through radial deposition additive manufacturing, Sci Rep, 4, 5357, 10.1038/srep05357 Reichardt, 2021, Advances in additive manufacturing of metal-based functionally graded materials, Int Mater Rev, 66, 1, 10.1080/09506608.2019.1709354 Li, 2022, Fabrication and characterization of stainless steel 308 L/Inconel 625 functionally graded material with continuous change in composition by dual-wire arc additive manufacturing, J Alloys Compd, 915, 10.1016/j.jallcom.2022.165398 Hofmann, 2014, Compositionally graded metals: a new frontier of additive manufacturing, J Mater Res, 29, 1899, 10.1557/jmr.2014.208 Kawasaki, 2002, Thermal fracture behavior of metal/ceramic functionally graded materials, Eng Fract Mech, 69, 1713, 10.1016/S0013-7944(02)00054-1 Li, 2020, A Review on functionally graded materials and structures via additive manufacturing: from multi-scale design to versatile functional properties, Adv Mater Technol, 5, 10.1002/admt.201900981 Shen, 2021, Fabrication of bulk Al-Co-Cr-Fe-Ni high-entropy alloy using combined cable wire arc additive manufacturing (CCW-AAM): microstructure and mechanical properties, J Mater Sci Technol, 74, 136, 10.1016/j.jmst.2020.10.037 Zhao, 2022, Microstructure and enhanced tensile properties of AlCoxCrFeNi high entropy alloys with high Co content fabricated by laser melting deposition, J Alloys Compd, 917, 10.1016/j.jallcom.2022.165403 Bobbio, 2018, Characterization of a functionally graded material of Ti-6Al-4V to 304L stainless steel with an intermediate V section, J Alloys Compd, 742, 1031, 10.1016/j.jallcom.2018.01.156 Wang, 2022, Research on plasma arc additive manufacturing of Inconel 625 Ni-Cu functionally graded materials, Mater Sci Eng, A, 853, 10.1016/j.msea.2022.143796 Zuback, 2019, Additive manufacturing of functionally graded transition joints between ferritic and austenitic alloys, J Alloys Compd, 770, 995, 10.1016/j.jallcom.2018.08.197 Mao, 2022, Effects of process parameters on interfacial characterization and mechanical properties of 316L/CuCrZr functionally graded material by selective laser melting, J Alloys Compd, 899, 10.1016/j.jallcom.2021.163256 Shen, 2016, Fabrication of Fe-FeAl functionally graded material using the wire-arc additive manufacturing process, Metall Mater Trans B, 47, 763, 10.1007/s11663-015-0509-5 Rodrigues, 2022, Steel-copper functionally graded material produced by twin-wire and arc additive manufacturing (T-WAAM), Mater Des, 213, 10.1016/j.matdes.2021.110270 Ghanavati, 2021, Additive manufacturing of thin-walled SS316L-IN718 functionally graded materials by direct laser metal deposition, J Mater Res Technol, 15, 2673, 10.1016/j.jmrt.2021.09.061 Carroll, 2016, Functionally graded material of 304L stainless steel and inconel 625 fabricated by directed energy deposition: characterization and thermodynamic modeling, Acta Mater, 108, 46, 10.1016/j.actamat.2016.02.019 Kumar, 2021, Microstructure and chemical composition analysis of double wire arc additive manufactured bimetallic structure, J Mater Eng Perform, 30, 5413, 10.1007/s11665-021-05819-9 Zhang, 2021, Effect of deposition sequence on microstructure and properties of 316L and inconel 625 bimetallic structure by wire arc additive manufacturing, J Mater Eng Perform, 30, 8972, 10.1007/s11665-021-06137-w Meng, 2020, Fabrication of steel-Inconel functionally graded materials by laser melting deposition integrating with laser synchronous preheating, Opt Laser Technol, 131, 10.1016/j.optlastec.2020.106451 Murr, 2011, Microstructural architecture, microstructures, and mechanical properties for a nickel-base superalloy fabricated by electron beam melting, Metall Mater Trans A, 42, 3491, 10.1007/s11661-011-0748-2 Wei, 2015, Evolution of solidification texture during additive manufacturing, Sci Rep, 5, 10.1038/srep16446 Lippold, 2005 Chen, 2020, Development and characterization of 316L/Inconel625 functionally graded material fabricated by laser direct metal deposition, Opt Laser Technol, 123, 10.1016/j.optlastec.2019.105916 Vashishtha, 2016, Effect of austenitic fillers on microstructural and mechanical properties of ultra-low nickel austenitic stainless steel, Sci Technol Weld Join, 21, 331, 10.1080/13621718.2015.1112604