Experimental investigation and numerical simulation of the effect of type of bending die on the quality of tube forming in rotary draw bending process

Soleimani, 2018, An Analytical Model and Numerical Simulations to Predict Process Parameters in the Tube Bending Under Internal Fluid Pressure, Amirkabir Journal of Mechanical Engineering, 53, 447 Soleimani, 2016, Embedding of internal fluid pressure investigation in mandrel through tube rotary draw bending of thin-walled tubes with critical bend radius, Modares Mechanical Engineering, 16, 287 Armstrong, 1954, Cold tube bending, US Patent El-Aty, 2023, A review on flexibility of free bending forming technology for manufacturing thin-walled complex-shaped metallic tubes, International Journal of Lightweight Materials and Manufacture, 6, 165, 10.1016/j.ijlmm.2022.09.007 Michalczyk, 2023, Mandrel-Free Bending of Tubes with Small Radii–A Theoretical and Experimental Study, Advances in Science and Technology, Research Journal, 17, 189 Jiang, 2023, Effect of bending radius on deformation behavior of H62 brass tubes in a less constrained free bending process, International Journal of Material Forming, 16 Safdarian, 2020, Investigation of tube fracture in the rotary draw bending process using experimental and numerical methods, International Journal of Material Forming, 13, 493, 10.1007/s12289-019-01484-5 Simonetto, 2022, Numerical modelling of Direct Hot Tube Rotary Draw Bending of 22MnB5 High Strength Steel, CIRP Journal of Manufacturing Science and Technology, 37, 547, 10.1016/j.cirpj.2022.03.003 Simonetto, 2021, In-process measurement of springback in tube rotary draw bending, The International Journal of Advanced Manufacturing Technology, 112, 2485, 10.1007/s00170-020-06453-w Zhu, 2020, Three-dimensional finite element modeling of rotary-draw bending of copper-titanium composite tube, The International Journal of Advanced Manufacturing Technology, 106, 2377, 10.1007/s00170-019-04781-0 Zardoshtian, 2018, Improvement of the rotary draw bending process in rectangular tubes by using internal fluid pressure, Int. J. Adv. Manuf .Technol., 95, 697, 10.1007/s00170-017-1255-4 Elyasi, 2017, Predicting the bending limit of AA8112 tubes using necking criterion in manufacturing of bent tubes, Int. J. Adv. Manuf. Technol., 88, 3307, 10.1007/s00170-016-9042-1 Elyasi, 2023, Investigating the effect of heat treatment in hydraulic rotary draw bending of AA6063 tubes, Modares Mechanical Engineering, 23, 257 Modanloo, 2023, The use of MCDM techniques to assess fluid pressure on the bending quality of AA6063 heat-treated tubes, Journal of Engineering Research, 10.1016/j.jer.2023.07.012 Xiao, 2007, Study on varying curvature push-bending technique of rectangular section tube", Journal of materials processing technology, 187, 476, 10.1016/j.jmatprotec.2006.11.190 Roein, 2021, Development of bending of AISI 304L micro-tubes with micro-wire mandrel and investigation of its effective parameters, Journal of Manufacturing Processes, 64, 723, 10.1016/j.jmapro.2021.02.029 Taghizadeh Rami, 2022, Improvement of rotary draw bending of commercial pure titanium tubes with resistance deformation and using steel ball, Modares Mechanical Engineering, 22, 371, 10.52547/mme.22.6.371 Roein, 2021, Introduction of a new method for bending of AISI 304L stainless steel micro-tubes with micro-wire mandrel, Journal of Manufacturing Processes, 66, 27, 10.1016/j.jmapro.2021.03.064 Heng, 2006, Forming characteristics of thin-walled tube bending process with small bending radius, Transactions of Nonferrous Metals Society of China, 16, 613, 10.1016/S1003-6326(06)60266-5