Experiment and simulation study on the specification parameters of finned heat sink for thermoelectric system in consideration of radiation among fins

Arshad, 2018, An experimental study of enhanced heat sinks for thermal management using n-eicosane as phase change material, Appl. Therm. Eng., 132, 52, 10.1016/j.applthermaleng.2017.12.066 Sakanova, 2018, Comparison of pin-fin and finned shape heat sink for power electronics in future aircraft, Appl. Therm. Eng., 136, 364, 10.1016/j.applthermaleng.2018.03.020 Liou, 2022, Revisit on the natural convection from horizontal multi-channel rectangular-fin heat sinks, Int. J. Therm. Sci., 171, 10.1016/j.ijthermalsci.2021.107232 Gong, 2020, A novel radiator structure for enhanced heat transfer used in PEM fuel cell vehicle, Int. J. Heat Mass Tran., 157, 10.1016/j.ijheatmasstransfer.2020.119926 Tiwary, 2022, Thermofluidic characteristic of a nanofluid-cooled oblique fin heat sink: an experimental and numerical investigation, Int. J. Therm. Sci., 171, 10.1016/j.ijthermalsci.2021.107214 Lineykin, 2020, Manufacturer-data-only-based modeling and optimized design of thermoelectric harvesters operating at low temperature gradients, Energy, 213, 10.1016/j.energy.2020.119015 Zhang, 2020, Thermal-hydraulic analysis of the thermoelectric space reactor power system with a potassium heat pipe radiator, Ann. Nucl. Energy, 136, 10.1016/j.anucene.2019.107018 Deng, 2021, Geometry design and performance optimization of a terrestrial radioisotope thermoelectric generator based on finite element analysis, Ann. Nucl. Energy, 151, 10.1016/j.anucene.2020.107883 Wang, 2020, Critical design features of thermal-based radioisotope generators: a review of the power solution for polar regions and space, Renew. Sustain. Energy Rev., 119, 10.1016/j.rser.2019.109572 Ambrosi, 2019, European radioisotope thermoelectric generators (RTGs) and radioisotope heater units (RHUs) for space science and exploration, Space Sci. Rev., 215, 10.1007/s11214-019-0623-9 Elankovan, 2019, Evaluation of thermoelectric power generated through waste heat recovery from long ducts and different thermal system configurations, Energy, 185, 477, 10.1016/j.energy.2019.07.039 Kim, 2019, Practical evaluation of electrical contact resistance of thermoelectric legs at high operation temperature, J. Mater. Sci. Mater. Electron., 30, 14112, 10.1007/s10854-019-01777-0 Wang, 2019, Experimental investigation of heat transfer and flow characteristics in finned copper foam heat sinks subjected to jet impingement cooling, Appl. Energy, 241, 433, 10.1016/j.apenergy.2019.03.040 Abbas, 2020, Augmentation of natural convection heat sink via using displacement design, Int. J. Heat Mass Tran., 154, 10.1016/j.ijheatmasstransfer.2020.119757 Sundar, 2019, Performance investigation of radial heat sink with circular base and perforated staggered fins, Int. J. Heat Mass Tran., 143, 10.1016/j.ijheatmasstransfer.2019.118526 Kalbasi, 2019, Studies on optimum fins number in PCM-based heat sinks, Energy, 171, 1088, 10.1016/j.energy.2019.01.070 Hong, 2020, Development of two-phase flow microchannel heat sink applied to solar-tracking high-concentration photovoltaic thermal hybrid system, Energy, 212 Mousavi, 2018, A novel heat sink design with interrupted, staggered and capped fins, Int. J. Therm. Sci., 127, 312, 10.1016/j.ijthermalsci.2018.02.003 Saha, 2019, Fully-developed natural convection in a periodic array of pin-fins, Int. J. Therm. Sci., 137, 325, 10.1016/j.ijthermalsci.2018.11.020 Song, 2022, Performance investigation of radial heat sink with pin fins placed normally on circular base edge, Int. J. Therm. Sci., 171, 10.1016/j.ijthermalsci.2021.107187 Ibrahim, 2020, The impact of square shape perforations on the enhanced heat transfer from fins: experimental and numerical study, Int. J. Therm. Sci., 149, 10.1016/j.ijthermalsci.2019.106144 Prajapati, 2019, Influence of fin height on heat transfer and fluid flow characteristics of rectangular microchannel heat sink, Int. J. Heat Mass Tran., 137, 1041, 10.1016/j.ijheatmasstransfer.2019.04.012 Haghighi, 2018, Natural convection heat transfer enhancement in new designs of plate-fin based heat sinks, Int. J. Heat Mass Tran., 125, 640, 10.1016/j.ijheatmasstransfer.2018.04.122 Li, 2020, Experimental research on vibration-enhanced heat transfer of fin-tube vehicle radiator, Appl. Therm. Eng., 180, 10.1016/j.applthermaleng.2020.115836 Shen, 2021, Experimental study on thermal and flow characteristics of metal foam heat pipe radiator, Int. J. Therm. Sci., 159, 10.1016/j.ijthermalsci.2020.106572 Akuto, 2020, An origami heat radiation fin for use in a stretchable thermoelectric generator, Micromachines, 11 Mulford, 2020, Experimental demonstration of heat loss and turn-down ratio for a multi-panel, actively deployed radiator, Appl. Therm. Eng., 178, 10.1016/j.applthermaleng.2020.115658 Lamba, 2017, Thermodynamic analysis of thermoelectric generator including influence of Thomson effect and leg geometry configuration, Energy Convers. Manag., 144, 388, 10.1016/j.enconman.2017.04.069 Wang, 2021, An optimized design approach concerning thermoelectric generators with frustum-shaped legs based on three-dimensional multiphysics model, Energy, 233