Estimation of Uncertainty for Contour Method Residual Stress Measurements
Tóm tắt
This paper describes a methodology for the estimation of measurement uncertainty for the contour method, where the contour method is an experimental technique for measuring a two-dimensional map of residual stress over a plane. Random error sources including the error arising from noise in displacement measurements and the smoothing of the displacement surfaces are accounted for in the uncertainty analysis. The output is a two-dimensional, spatially varying uncertainty estimate such that every point on the cross-section where residual stress is determined has a corresponding uncertainty value. Both numerical and physical experiments are reported, which are used to support the usefulness of the proposed uncertainty estimator. The uncertainty estimator shows the contour method to have larger uncertainty near the perimeter of the measurement plane. For the experiments, which were performed on a quenched aluminum bar with a cross section of 51 × 76 mm, the estimated uncertainty was approximately 5 MPa (σ/E = 7 · 10−5) over the majority of the cross-section, with localized areas of higher uncertainty, up to 10 MPa (σ/E = 14 · 10−5).
Tài liệu tham khảo
Prime MB (2001) Cross-sectional mapping of residual stresses by measuring the surface contour after a cut. J Eng Mater Technol 123(2):162–168
Kelleher J, Prime MB, Buttle D, Mummery PM, Webster PJ, Shackleton J, Withers PJ (2003) The measurement of residual stress in railway rails by diffraction and other methods. J Neutron Res 11(4):187–193. doi:10.1080/10238160410001726602
Brown DW, Holden TM, Clausen B, Prime MB, Sisneros TA, Swenson H, Vaja J (2011) Critical comparison of two independent measurements of residual stress in an electron-beam welded uranium cylinder: neutron diffraction and the contour method. Acta Mater 59(3):864–873. doi:10.1016/j.actamat.2010.09.022
Prime MB, DeWald AT (2013) The contour method. In: Schajer GS (ed) Practical residual stress measurement methods. Wiley, West Sussex
DeWald AT, Rankin JE, Hill MR, Lee MJ, Chen H-L (2004) Assessment of tensile residual stress mitigation in alloy 22 welds due to laser peening. J Eng Mater Technol 126(4):465. doi:10.1115/1.1789957
Bell S (1999) Measurement good practice guide: a beginner’s guide to uncertainty of measurement. National Physical Laboratory, Teddington, Middlesex
Bevington PR, Robinson DK (1969) Data reduction and error analysis for the physical sciences, vol 2. McGraw-Hill New York
Taylor JR (1997) An introduction to error analysis: the study of uncertainties in physical measurements. University Science Books
Coleman HW, Steele WG (2009) Chapter 2. In: experimentation, validation, and uncertainty analysis for engineers, 3rd edn. Wiley, Hoboken, New Jersey
Hosseinzadeh F, Ledgard P, Bouchard PJ (2012) Controlling the cut in contour residual stress measurements of electron beam welded Ti-6Al-4 V alloy plates. Exp Mech 53(5):829–839. doi:10.1007/s11340-012-9686-1
Prime MB, Gnäupel-Herold T, Baumann JA, Lederich RJ, Bowden DM, Sebring RJ (2006) Residual stress measurements in a thick, dissimilar aluminum-alloy friction stir weld. Acta Mater 54(15):4013–4021
Hosseinzadeh F, Bouchard PJ (2012) Mapping multiple components of the residual stress tensor in a large P91 steel pipe girth weld using a single contour cut. Exp Mech 53(2):171–181. doi:10.1007/s11340-012-9627-z
Prime MB, Sebring RJ, Edwards JM, Hughes DJ, Webster PJ (2004) Laser surface-contouring and spline data-smoothing for residual stress measurement. Exp Mech 44(2):176–184. doi:10.1177/00144851039762
Prime MB, Hill MR (2006) Uncertainty, model error, and order selection for series-expanded, residual-stress inverse solutions. J Eng Mater Technol 128(2):175. doi:10.1115/1.2172278
Hammersley JM, Handscomb DC (1964) Monte Carlo methods. Halsted Press
Hill MR, Olson MD (2014) Repeatability of the contour method for residual stress measurement. Exp Mech 54:1269–1277. doi:10.1007/s11340-014-9867-1
SAE Aerospace (2006) Heat treatment of wrought aluminum alloy parts.
Robinson JS, Tanner DA, Truman CE, Paradowska AM, Wimpory RC (2012) The influence of quench sensitivity on residual stresses in the aluminium alloys 7010 and 7075. Mater Charact 65:73–85. doi:10.1016/j.matchar.2012.01.005
Shin SH (2005) FEM analysis of plasticity-induced error on measurement of welding residual stress by the contour method. J Mech Sci Technol 19(10):1885–1890. doi:10.1007/BF02984267
Traoré Y, Hosseinzadeh F, Bouchard PJ (2014) Plasticity in the contour method of residual stress measurement. In: Advanced Materials Research. Trans Tech Publ, pp 337–342
Mahmoudi AH, Hosseinzadeh AR, Jooya M (2013) Plasticity Effect on residual stresses measurement using contour method. International Journal of Engineering 26 (10 (A)). doi:10.5829/idosi.ije.2013.26.10a.10
Prime MB, Kastengren AL (2011) The contour method cutting assumption: error minimization and correction. In: Proulx T (ed) Experimental and Applied Mechanics, Volume 6, vol 17. Conference Proceedings of the Society for Experimental Mechanics Series. Springer New York, pp 233–250. Currently available at http://www.lanl.gov/contour/. doi:10.1007/978-1-4419-9792-0_40