Entire mechanical analysis of prestressed CFRP strengthened RC beams under different prestressed introduced methods
Tóm tắt
In order to clarify the effect of mechanical tensioning and SMA wire heating recovery on introducing prestress into CFRP sheet strengthened reinforced concrete (RC) beams, an experimental research on the bending performance of prestressed CFRP sheet strengthened RC beams was conducted. Based on the test results, a bending carrying capacity model for RC beams externally strengthened with prestressed CFRP sheets was proposed. The model provides calculation methods for the decompression moment, cracking moment, yielding moment, and ultimate moment, corresponding to different failure modes of the RC beams strengthened with externally bonded prestressed CFRP sheets. Four experimental beams were designed to verify the accuracy of the model with the prestresses of 100 MPa and 200 MPa. The results show that during the yield stage and strengthening stage, the loading-unloading stress-strain relationship curves of SMA wire under different prestrains are basically consistent. When the prestrain of SMA wire is 10%, the maximum recovery stress reaches 448.5 MPa. Under the same prestrain conditions, the maximum recovery stress of CFRP sheets was reduced by 37.8–39.5% when the prestress was introduced through heating recovery of SMA wires. The failure mode of mechanically tensioned prestressed CFRP sheet strengthened beams is the CFRP sheet debonding caused by mid-span bending cracks, while the failure mode of strengthened beams with prestressed CFRP sheet by SMA wire heating recovery is the CFRP sheet end debonding. The cracking moment and yield moment of the strengthened beams are significantly increased by two methods of introducing prestressing. The stiffness improvement of mechanically tensioned prestressed CFRP sheet strengthened beam is relatively large. While, the prestressed CFRP sheet strengthened beam by SMA wire heating recovery gradually experience end peeling failure of the CFRP sheet, and the prestressing effect does not effectively limit the development of cracks, resulting in limited stiffness improvement. The calculation results are in good agreement with the experimental results, proving that the proposed method for analyzing the entire bending process can be used to predict the bending mechanical properties of the prestressed CFRP sheet strengthened beams.
Từ khóa
Tài liệu tham khảo
Basaran B, Kalkan I (2020) Investigation on variables affecting bond strength between FRP reinforcing bar and concrete by modified hinged beam tests. Compos Struct 242:112185
Derkowski W, Walczak R (2021) Possibilities of increasing effectiveness of RC structure strengthening with FRP materials. Mater (Basel) 14(6):1387
Feng P, Lu XZ, Ye LP (2011) Application technology of fiber-reinforced composite materials in construction engineering. China Architecture & Building, Beijing
Frigione M, Lettieri M (2018) Durability issues and challenges for material advancements in FRP employed in the construction industry. Polymers 10(3):247
Hassan WM, Hodhod OA, Hilal MS, Bahnasaway HH (2021) Tests on FRP-retrofitted tension-controlled eccentric and biaxial high strength concrete columns. Compos Struct 276:114536
Hui YX, Xue YJ, Wang WW, Tan X (2022) FRP/SMA experimental study on mechanical performance and recoverable performance of Composite materials. J Compos Sci 39:1–15
Koteš P, Vavruš M, Jošt J, Prokop J (2020) Strengthening of concrete column by using the wrapper layer of fibre reinforced concrete. Materials 13(23):5432
Kueres S, Will N, Hegger J (2020) Shear strength of pre-stressed FRP reinforced concrete beams with shear reinforcement. Eng Struct 206:110088
Wang WW (2007) FRP strengthening technology and application of reinforced concrete structures. China Architecture & Building, Beijing
GB 50010-2010 (2010) Code for design of concrete structures [S]. China Architecture and Construction Press, Beijing
JTG 3362-2018 (2018) Specifications for Design of Highway Reinforced Concrete and Prestressed Concrete Bridges and Culverts [S]. China Communication Press, Beijing
Shi JZ (2021) Research progress on externally prestressed fiber-reinforced resin-based composite reinforced concrete structures. J Compos Sci 38(07):2092–2106
Soleilhet F, Quiertant M, Benzarti K (2023) Numerical modelling of the nonlinear shear creep behavior of FRP-Concrete Bonded joints. Materials 16(2):801
Teng JG, Yao J (2007) Plate end debonding in FRP-plated RC beams-II: strength model. Eng Struct 29(10):2472–2486
Tiwary AK, Singh S, Kumar R, Sharma K, Chohan JS, Sharma S, Singh J, Kumar J, Deifalla AF (2022) Comparative study on the behavior of reinforced concrete beam retrofitted with CFRP strengthening techniques. Polymers 14(19):4024
Wang WW, Dai JG, Harries KA (2013) Performance evaluation of RC beams strengthened with an externally Bonded FRP system under simulated vehicle loads. J Bridge Engineering 18(1):76–82
Wang WW, Dai JG, Harries KA, Bao QH (2012) Pre-stress losses and flexural behavior of reinforced concrete beams strengthened with posttensioned CFRP sheets. J Compos Constr 16(2):207–216
Xue Y-J, Cai D-C, Wang W-W, Tian J (2023) Jing-Shui Zhen, Bo-Cheng Li. Pre-stress loss and flexural behavior of precracked RC beams strengthened with FRP/SMA composites. Compos Struct 321:117319
Xue Y-J, Wang WW, Tan X, Hui YX, Tian J (2022) Zhong Feng Zhu. Mechanical behavior and recoverable properties of CFRP shape memory alloy composite under different pre-strains. Constr Build Mater 333:127186
Zhang L, Wang WW, Harries KA, Tian J (2015) Bonding behavior of Wet-Bonded GFRP-Concrete interface. J Compos Constr 19(6):04015001