Effects of manufacturing errors on tribological characteristics of 3-D textured micro- thrust bearings

Abramovitz, 1955, Theory for a Slider Bearing with a Convex Pad Surface; Side Flow Neglected, Journal of Franklin Institute, 259, 221, 10.1016/0016-0032(55)90827-9 Andharia, 2000, On the Shape of the Lubricant Film for the Optimum Performance of a Longitudinal Rough Slider Bearing, Industrial Lubrication and Tribology, 52, 273, 10.1108/00368790010352682 Bhat, 2010, Performance Analysis of Pareto Optimal Bearings Subject to Surface Error Variations, Tribology International, 43, 2240, 10.1016/j.triboint.2010.07.012 Buscaglia, 2005, The Effect of Periodic Textures on the Static Characteristics of Thrust Bearings, ASME Journal of Tribology, 127, 899, 10.1115/1.2033896 Cheng, 1995, A Selection Strategy for the Design of Externally Pressurized Journal Bearings, Tribology International, 28, 465, 10.1016/0301-679X(95)00011-R Chen, 2006, The Effect of Recess Shape on Performance Analysis of the Gas-Lubricated Bearing in Optical Lithography, Tribology International, 39, 1336, 10.1016/j.triboint.2005.10.005 Dobrica, 2009, About the Validity of Reynolds Equation and Inertia Effects in Textured Sliders of Infinite Width, Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, 223, 69, 10.1243/13506501JET433 Etsion, 2004, Experimental Investigation of Laser Surface Textured Parallel Thrust Bearings, Tribology Letters, 17, 295, 10.1023/B:TRIL.0000032467.88800.59 Kwan, 2000, A Tolerancing Procedure for Inherently Compensated, Rectangular Aerostatic Thrust Bearings, Tribology International, 33, 581, 10.1016/S0301-679X(00)00109-2 Li, 2007, Influences of the Geometrical Parameters of Aerostatic Thrust Bearing with Pocketed Orifice-type Restrictor on its Performance, Tribology International, 40, 1120, 10.1016/j.triboint.2006.11.001 Ozalp, 2006, Optimum Surface Profile Design and Performance Evaluation of Inclined Slider Bearings, Current Science, 90, 1480 Papadopoulos, 2011, Evolutionary Optimization of Micro-Thrust Bearings with Periodic Partial Trapezoidal Surface Texturing, Journal of Engineering for Gas Turbines and Power, 133, 1, 10.1115/1.4001990 Papadopoulos, 2011, Geometry Optimization of Textured 3-D Micro-thrust Bearings, Journal of Tribology, 133, 1, 10.1115/1.4004990 Pascovici, 2009, Analytical Investigation of a Partially Textured Parallel Slider, Proceedings of the Institution of Mechanical Engineers, Part J: Journal of Engineering Tribology, 223, 151, 10.1243/13506501JET470 Puri, 1983, The Analysis of a Pivoted Porous Slider Bearing with a Convex Pad Surface, Wear, 88, 127, 10.1016/S0043-1648(83)80002-7 Ramanaiah, 1982, Effect of Bearing Deformation on the Characteristics of a Slider Bearing, Wear, 78, 273, 10.1016/0043-1648(82)90237-X Sharma, 2009, Experimental Studies of Pressure Distributions in Finite Slider Bearing with Single Continuous Surface Profiles on the Pads, Tribology International, 42, 1040, 10.1016/j.triboint.2009.02.010 Stout, 1980, Orifice Compensated EP Gas Bearings: The Significance of Errors of Manufacture, Tribology International, 13, 105, 10.1016/0301-679X(80)90052-3 Tonder, 1987, Effects of Skew Unidirectional Striated Roughness on Hydrodynamic Lubrication, Wear, 115, 19, 10.1016/0043-1648(87)90194-3 Yang, 2009, Rapid Manufacturing of Non-assembly Complex Micro-devices by Stereolithography, Tsinghua Science and Technology, 14, 164, 10.1016/S1007-0214(09)70086-0