Effect of ball burnishing process on surface roughness and corrosion behavior of S235JR steel
The International Journal of Advanced Manufacturing Technology - Trang 1-14 - 2024
Tóm tắt
Degradation caused by corrosion is a major problem for S235JR steel and is responsible for many failures. Ball burnishing is a superficial mechanical finishing treatment that improves surface quality as well as its mechanical properties. The aim of this experimental work is to study the influence of this process on the surface quality and corrosion behavior of S235JR steel. The response surface method (RSM), based on Box-Behnken experimental design, was used to minimize the surface roughness, which has a significant influence on corrosion resistance. “Ra” and “Rz” roughness measurements, as well as 3D surface topography observations, were carried out. Furthermore, the subsurface microhardness distribution was examined, and an X-ray diffraction analysis was performed. The polarization technique (Tafel) and electrochemical impedance spectroscopy (EIS) were used to evaluate corrosion resistance. Finally, analysis by scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS) was carried out before and after the corrosion tests. The results showed that burnishing force and ball diameter are the main parameters influencing roughness. The optimal regime reduced roughness “Ra” and “Rz” by more than 96% and 97% respectively, producing a smooth and uniform topography. XRD analysis revealed surface grain refinement without phase change. The subsurface microhardness increased to a depth of 40 μm, suggesting a burnished layer of equivalent thickness. Electrochemical corrosion tests and SEM observation showed that the corrosion resistance of the burnished surface was significantly improved, mainly attributed to grain refinement.
Tài liệu tham khảo
Golafshani MG, Tavakoli H (2023) Corrosion and electrochemical characterization of St37 in the presence of quince extract as a green and sustainable inhibitor. Electrocatalysis 14(2):279–293. https://doi.org/10.1007/s12678-022-00788-6
Singh G, Singh D, Dhindsa GS, Singh G, Singh P (2020) Corrosion in aircraft components: types, impacts and protection measures. Int J Adv Sci Technol 29:4891–4896
Uddin M, Hall C, Santos V, Visalakshan R, Qian G, Vasilev K (2021) Synergistic effect of deep ball burnishing and HA coating on surface integrity, corrosion and immune response of biodegradable AZ31B Mg alloys. Mater Sci Eng, C 118:111459. https://doi.org/10.1016/j.msec.2020.111459
Santos V, Uddin M, Hall C (2023) Mechanical surface treatments for controlling surface integrity and corrosion resistance of Mg alloy implants: a review. J Funct Biomater 14(5):242. https://doi.org/10.3390/jfb14050242
Attabi S, Himour A, Laouar L, Motallebzadeh A (2021) Mechanical and wear behaviors of 316L stainless steel after ball burnishing treatment. J Market Res 15:3255–3267. https://doi.org/10.1016/j.jmrt.2021.09.081
Saldaña-Robles A, Plascencia-Mora H, Aguilera-Gómez E, Saldaña-Robles A, Marquez-Herrera A, Diosdado-De la Peña JA (2018) Influence of ball-burnishing on roughness, hardness and corrosion resistance of AISI 1045 steel. Surf Coat Technol 339:191–198. https://doi.org/10.1016/j.surfcoat.2018.02.013
Laouar L, Hamadache H, Saad S, Bouchelaghem A, Mekhilef S (2009) Mechanical surface treatment of steel-optimization parameters of regime. Phys Procedia 2(3):1213–1221. https://doi.org/10.1016/j.phpro.2009.11.084
Charfeddine Y, Youssef S, Sghaier S, Sghaier J, Hamdi H (2021) Study of the simultaneous grinding/ball-burnishing of AISI 4140 based on finite element simulations and experiments. Int J Mech Sci 192:106097. https://doi.org/10.1016/j.ijmecsci.2020.106097
Travieso-Rodríguez JA, Jerez-Mesa R, Gómez-Gras G, Llumà-Fuentes J, Casadesús-Farràs O, Madueño-Guerrero M (2019) Hardening effect and fatigue behavior enhancement through ball burnishing on AISI 1038. J Market Res 8(6):5639–5646. https://doi.org/10.1016/j.jmrt.2019.09.032
Cagan SC, Pruncu CI, Buldum BB (2020) An investigation into ball burnishing process of magnesium alloy on CNC lathe using different environments. J Magnes Alloys 8(4):1061–1070. https://doi.org/10.1016/j.jma.2020.06.008
Attabi S, Himour A, Laouar L, Motallebzadeh A (2021) Effect of ball burnishing on surface roughness and wear of AISI 316L SS. J Bio-and Tribo-Corrosion 7:1–11. https://doi.org/10.1007/s40735-020-00437-9
Nguyen TT, Cao LH, Nguyen TA, Dang XP (2020) Multi-response optimization of the roller burnishing process in terms of energy consumption and product quality. J Clean Prod 245:119328. https://doi.org/10.1016/j.jclepro.2019.119328
Bourebia M, Hamadache H, Lakhdar L, Mentouri Z, Kamila D, Tarek H, Ahlem T (2021) Effect of ball burnishing process on mechanical properties and impact behavior of S355JR steel. Int J Adv Manuf Technol 116:1373–1384. https://doi.org/10.1007/s00170-021-07454-z
Revankar GD, Shetty R, Rao SS, Gaitonde VN (2017) Wear resistance enhancement of titanium alloy (Ti–6Al–4V) by ball burnishing process. J Market Res 6(1):13–32. https://doi.org/10.1016/j.jmrt.2016.03.007
Teimouri R, Amini S, Bami AB (2018) Evaluation of optimized surface properties and residual stress in ultrasonic assisted ball burnishing of AA6061-T6. Measurement 116:129–139. https://doi.org/10.1016/j.measurement.2017.11.001
Uddin M, Santifoller R, Hall C, Schlaefer T (2023) Effect of combined grinding–burnishing process on surface integrity, tribological, and corrosion performance of laser-clad Stellite 21 alloys. Adv Eng Mater 25(8):2201332. https://doi.org/10.1002/adem.202201332
Silva-Álvarez DF, Márquez-Herrera A, Saldaña-Robles A, Zapata-Torres M, Mis-Fernández R, Peña-Chapa JL, Moreno-Palmerín J, Hernández-Rodríguez E (2020) Improving the surface integrity of the CoCrMo alloy by the ball burnishing technique. J Market Res 9(4):7592–7601. https://doi.org/10.1016/j.jmrt.2020.05.038
Tang J, Luo HY, Zhang YB (2017) Enhancing the surface integrity and corrosion resistance of Ti-6Al-4V titanium alloy through cryogenic burnishing. Int J Adv Manuf Technol 88:2785–2793. https://doi.org/10.1007/s00170-016-9000-y
Li B, Duan Y, Zheng S, Li M, Peng M, Qi H (2023) Microstructural homogeneity, texture and corrosion properties of RE-doped 55Mg-35Pb-9.2 Al-0.8 B alloy fabricated via equal channel angular pressing (ECAP). J Alloys Compounds 966:171607. https://doi.org/10.1016/j.jallcom.2023.171607
Li G, Pan X, Jiang J, Li J, Xie L, Liu H, Zhang M (2023) Achieving ultra-fine grains and high corrosion resistance of Al–Zn–Mg–Cu alloy by ECAP and post cold rolling. J Market Res 26:7354–7368. https://doi.org/10.1016/j.jmrt.2023.09.070
Ganguly S, Chaubey AK, Gope R, Kushwaha A, Basu A, Gupta M (2023) Enhanced corrosion performance of ultrasonically shot peened and graphene nanoparticles reinforced squeeze-cast AZ91 magnesium alloy. J Alloy Compd 966:171203. https://doi.org/10.1016/j.jallcom.2023.171203
Jinlong L, Hongyun L, Tongxiang L (2016) Investigation of microstructure and corrosion behavior of burnished aluminum alloy by TEM, EWF, XPS and EIS techniques. Mater Res Bull 83:148–154. https://doi.org/10.1016/j.materresbull.2016.05.013
Pu Z, Song GL, Yang S, Outeiro JC, Dillon OW Jr, Puleo DA, Jawahir IS (2012) Grain refined and basal textured surface produced by burnishing for improved corrosion performance of AZ31B Mg alloy. Corros Sci 57:192–201. https://doi.org/10.1016/j.corsci.2011.12.018
Ramesh S, Anne G, Bhat N, Aithal G, Nayaka HS, Arya S (2021) Surface modification of multi-directional forged biodegradable Mg-Zn alloy by ball burnishing process: modeling and analysis using deep neural network. J Manuf Process 68:423–434. https://doi.org/10.1016/j.jmapro.2021.05.049
Goupy J (1999) Plans d’expériences pour surfaces de réponse. Dunod, Paris
Su H, Shen X, Xu C, He J, Wang B, Su G (2020) Surface characteristics and corrosion behavior of TC11 titanium alloy strengthened by ultrasonic roller burnishing at room and medium temperature. J Market Res 9(4):8172–8185. https://doi.org/10.1016/j.jmrt.2020.05.059
Marteau J, Bigerelle M, Mazeran PE, Bouvier S (2015) Relation between roughness and processing conditions of AISI 316L stainless steel treated by ultrasonic shot peening. Tribol Int 82:319–329. https://doi.org/10.1016/j.triboint.2014.07.013
John MS, Wilson AW, Bhardwaj AP, Abraham A, Vinayagam BK (2016) An investigation of ball burnishing process on CNC lathe using finite element analysis. Simul Model Pract Theory 62:88–101. https://doi.org/10.1016/j.simpat.2016.01.004
Bourebia M, Laouar L, Hamadache H, Dominiak S (2017) Improvement of surface finish by ball burnishing: approach by fractal dimension. Surf Eng 33(4):255–262. https://doi.org/10.1080/02670844.2016.1232778
Chomienne V, Valiorgue F, Rech J, Verdu C (2016) Influence of ball burnishing on residual stress profile of a 15–5PH stainless steel. CIRP J Manuf Sci Technol 13:90–96. https://doi.org/10.1016/j.cirpj.2015.12.003
Berkani M, Bouchareb MK, Bouhelassa M, Kadmi Y (2020) Photocatalytic degradation of industrial dye in semi-pilot scale prototype solar photoreactor: optimization and modeling using ANN and RSM based on Box-Wilson approach. Top Catal 63:964–975. https://doi.org/10.1007/s11244-020-01320-0
Wood IG, Vočadlo L, Dobson DP, Price GD, Fortes AD, Cooper FJ, Neale JW, Walker AM, Marshall WG, Tucker MG, Francis DJ, Stone HJ, McCammon CA (2008) Thermoelastic properties of magnesiowüstite,(Mg1− xFex) O: determination of the Anderson-Grüneisen parameter by time-of-flight neutron powder diffraction at simultaneous high pressures and temperatures. J Appl Crystallogr 41(5):886–896. https://doi.org/10.1107/S0021889808025417
Kalisz J, Żak K, Wojciechowski S, Gupta MK, Krolczyk GM (2021) Technological and tribological aspects of milling-burnishing process of complex surfaces. Tribol Int 155:106770. https://doi.org/10.1016/j.triboint.2020.106770
Wang Z, Xiao Z, Huang C, Wen L, Zhang W (2017) Influence of ultrasonic surface rolling on microstructure and wear behavior of selective laser melted Ti-6Al-4V alloy. Materials 10(10):1203. https://doi.org/10.3390/ma10101203
Chi G, Yi D, Liu H (2020) Effect of roughness on electrochemical and pitting corrosion of Ti-6Al-4V alloy in 12 wt.% HCl solution at 35 C. J Mater Res Technol 9(2):1162–1174. https://doi.org/10.1016/j.jmrt.2019.11.044