Dynamic modeling and nonlinear vibration analysis of spindle system during ball end milling process
Tóm tắt
In cutting process, the insufficiency in grasp of the tool vibration characteristics of spindle system seriously hinders the improvement of machining quality and efficiency. Thus, this paper develops a novel dynamic model of spindle system in ball end milling process considering the nonlinear contact behavior of bearings. For the sake of coupling with the motion differential equations of spindle shaft, a general analytical expression for the nonlinear contact force of matched angular contact ball bearings is proposed. Then, dynamic cutting force model during ball end milling is established with consideration of the influence of tool vibration on the uncut chip thickness. Furthermore, the effectiveness and feasibility of the proposed model is confirmed by some cutting tests. Finally, the effects of rotation speed, bearing preload, and cutting parameters on the tool end vibration response of spindle system are analyzed in detail. The investigations reveal that the main resonance frequency increases and the corresponding resonance amplitude decreases as bearing preload increases. The larger bearing preload can improve cutting stability and machining quality. It is also concluded that the change regarding axial depth of cut considerably affects the vibration behaviors of tool end. The proposed dynamic model can be applied to predict the vibration of spindle system during ball end milling, especially the tool vibration.
Tài liệu tham khảo
Chao S, Altintas Y (2016) Chatter free tool orientations in 5-axis ball-end milling. Int J Mach Tools Manuf 106:89–97
Abele E, Altintas Y, Brecher C (2010) Machine tool spindle units. CIRP Ann-Manuf Technol 59:781–802
Zhang J, Liu C (2019) Chatter stability prediction of ball-end milling considering multi-mode regenerations. Int J Adv Manuf Technol 100:131–142
Aini R, Rahnejat H, Gohar R (1990) A five degrees of freedom analysis of vibrations in precision spindles. Int J Mach Tools Manuf 30:1–18
Alfares M, Elsharkawy A (2000) Effect of grinding forces on the vibration of grinding machine spindle system. Int J Mach Tools Manuf 40:2003–2030
Alfares M, Elsharkawy A (2003) Effects of axial preloading of angular contact ball bearings on the dynamics of a grinding machine spindle system. J Mater Process Technol 136:48–59
Karacay T, Akturk N (2008) Vibrations of a grinding spindle supported by angular contact ball bearings. Proc Inst Mech Eng Pt K-J Multi-Body Dyn 222:61–75
Zhang SJ, To S, Cheung CF, Wang HT (2012) Dynamic characteristics of an aerostatic bearing spindle and its influence on surface topography in ultra-precision diamond turning. Int J Mach Tools Manuf 62:1–12
Zhang SJ, To S, Wang HT (2013) A theoretical and experimental investigation into five-DOF dynamic characteristics of an aerostatic bearing spindle in ultra-precision diamond turning. Int J Mach Tools Manuf 71:1–10
Zhang SJ, To S (2013) The effects of spindle vibration on surface generation in ultra-precision raster milling. Int J Mach Tools Manuf 71:52–56
Gao SH, Long XH, Meng G (2008) Nonlinear response and nonsmooth bifurcations of an unbalanced machine-tool spindle-bearing system. Nonlinear Dyn 54:365–377
Miao H, Li C, Wang C, Xu M, Zhang Y (2021) The vibration analysis of the CNC vertical milling machine spindle system considering nonlinear and nonsmooth bearing restoring force. Mech Syst Signal Proc 161:107970
Cao Y, Altintas Y (2004) A general method for the modeling of spindle-bearing systems. J Mech Design 126:1089–1104
Cao H, Shi F, Li Y, Li B, Chen X (2019) Vibration and stability analysis of rotor-bearing-pedestal system due to clearance fit. Mech Syst Signal Proc 133:106275
Xi S, Cao H, Chen X, Niu L (2018) A dynamic modeling approach for spindle bearing system supported by both angular contact ball bearing and floating displacement bearing. J Manuf Sci Eng-Trans ASME 140:021014
Xi S, Cao H, Chen X (2019) Dynamic modeling of spindle bearing system and vibration response investigation. Mech Syst Signal Proc 133:106275
Hong SW, Tong VC (2016) Rolling-element bearing modeling: a review. Int J Precis Eng Man 17:1729–1749
Xu M, Cai B, Li C, Zhang H, Liu Z, He D, Zhang Y (2020) Dynamic characteristics and reliability analysis of ball screw feed system on a lathe. Mech Mach Theory 150:103890
Wang W, Zhou Y, Wang H, Li C, Zhang Y (2019) Vibration analysis of a coupled feed system with nonlinear kinematic joints. Mech Mach Theory 134:562–581
Noel D, Ritou M, Furet B, Le Loch S (2013) Complete analytical expression of the stiffness matrix of angular contact ball bearings. J Tribol-Trans ASME 135:041101
Liu Y, Zhang Y (2019) A research on the time-varying stiffness of the ball bearing considering the time-varying number of laden balls and load distribution. Proc Inst Mech Eng Part C-J Eng Mech Eng Sci 233:4381–4396
Gunduz A, Singh R (2013) Stiffness matrix formulation for double row angular contact ball bearings: Analytical development and validation. J Sound Vibr 332:5898–5916
Xu T, Yang L, Wu W, Wang K (2021) Effect of angular misalignment of inner ring on the contact characteristics and stiffness coefficients of duplex angular contact ball bearings. Mech Mach Theory 157:104178
Wojciechowski S, Twardowski P (2012) Tool life and process dynamics in high speed ball end milling of hardened steel. Procedia CIRP 1:289–294
Lee P, Altintas Y (1996) Prediction of ball–end milling forces from orthogonal cutting data. Int J Mach Tools Manuf 36:1059–1072
Wojciechowski S, Twardowski P, Pelic M (2014) Cutting forces and vibrations during ball end milling of inclined surfaces. Procedia CIRP 14:113–118
Wojciechowski S, Chwalczuk T, Twardowski P, Krolczyk GM (2015) Modeling of cutter displacements during ball end milling of inclined surfaces. Arch Civ Mech Eng 15:798–805
Wojciechowski S, Twardowski P, Pelic M, Maruda RW, Barrans S, Krolczyk GM (2016) Precision surface characterization for finish cylindrical milling with dynamic tool displacements model. Precis Eng-J Int Soc Precis Eng Nanotechnol 46:158–165
Wojciechowski S, Mrozek K (2017) Mechanical and technological aspects of micro ball end milling with various tool inclinations. Int J Mech Sci 134:424–435
Wojciechowski S, Maruda RW, Nieslony P, Krolczyk GM (2016) Investigation on the edge forces in ball end milling of inclined surfaces. Int J Mech Sci 119:360–369
Honeycutt A, Schmitz TL (2016) A new metric for automated stability identification in time domain milling simulation. J Manuf Sci Eng-Trans ASME 138:074501
Sonawane H, Joshi SS (2018) Modeling of chip geometry in ball-end milling of superalloy using strains in deformed chip (SDC) approach. Int J Mach Tools Manuf 130:49–64
Wei ZC, Wang MJ, Zhu JN, Gu LY (2011) Cutting force prediction in ball end milling of sculptured surface with Z-level contouring tool path. Int J Mach Tools Manuf 51:428–432
Wang JJ, Zheng CM (2002) Identification of shearing and ploughing cutting constants from average forces in ball-end milling. Int J Mach Tools Manuf 42:695–705
Wang C, Ding P, Huang X, Li H (2021) A method for predicting ball-end cutter milling force and its probabilistic characteristics. Mech Based Des Struct Mech
Lamikiz A, Lopez De Lacalle LN, Sanchez JA, Bravo U (2005) Calculation of the specific cutting coefficients and geometrical aspects in sculptured surface machining. Mach Sci Technol 9:411–436
Ma H, Li H, Zhao X, Niu H, Wen B (2013) Effects of eccentric phase difference between two discs on oil-film instability in a rotor-bearing system. Mech Syst Signal Proc 41:526–545
Harris TA (2001) Rolling Bearing Analysis, John Wiley & Sons
Li J, Murat Kilic Z, Altintas Y (2021) General cutting dynamics model for five-axis ball-end milling operations. J Manuf Sci Eng-Trans ASME 142:121003
Bathe KJ, Wilson EL (1976) Numerical methods in finite element analysis. Prentice-Hall, New Jersey
Chandra NH, Sekhar AS (2014) Swept sine testing of rotor-bearing system for damping estimation. J Sound Vib 333:604–620