Nội dung được dịch bởi AI, chỉ mang tính chất tham khảo
Đo lường và Tính toán Dämpung Modal như Một Mô Tả Gần Đúng cho Các Hệ Thống Thực Tế
Tóm tắt
Theo công nghệ hiện tại, việc dự đoán chính xác đặc điểm tiếng ồn của một hệ thống truyền động điện là không khả thi. Một thách thức là mô tả động lực học cấu trúc, đặc biệt là mô hình hóa độ damping. Nguyên nhân là do nhiều cơ chế không tuyến tính khác nhau góp phần vào độ damping. Trong số đó, có thể kể đến độ damping vật liệu, sự phát ra âm thanh và độ damping tại các điểm nối. Trong nghiên cứu này, các độ damping modal phù hợp cho một EMKS được tính toán dựa trên các thân nhôm, bằng cách xem xét độc lập các đóng góp từ độ damping vật liệu và sự phát ra âm thanh. Các thách thức trong việc đo lường độ damping để xác thực sẽ được trình bày chi tiết. Lỗi do mô hình hóa một hệ thống không tỷ lệ thông qua độ damping tỷ lệ sẽ được ước tính dựa trên một FRF đã được tính toán. Phương pháp này áp dụng cho các vật liệu orthotropic và về nguyên tắc có thể bao gồm cả độ damping tại các điểm nối.
Từ khóa
#độ damping modal #hệ thống truyền động điện #mô hình hóa độ damping #vật liệu orthotropic #đo lường độ dampingTài liệu tham khảo
Bambton MCC Jr., Craig RR (1968) Coupling of substructures for dynamic analyses. AIAA J 6(7):1313–1319
Ewins DJ (2000) Modal testing: theory, practice and application, 2. Aufl. Research Studies,
Wegerhoff M (2017) Methodik zur numerischen NVH Analyse eines elektrifizierten PKW Antriebsstrangs. Ph.D. Dissertation, RWTH Aachen University
Humbert L, Pellerey P, Cristaudo S (2012) Electromagnetic and structural coupled simulation to investigate NVH behavior of an electrical automotive powertrain. SAE Int J Alt Power 1(2):395–404. https://doi.org/10.4271/2012-01-1523
Audenina AL, Calderdale PM (1996) Measurement of non-linear internal damping in metals: processing of decay signals in a uniaxial stress field. J Sound Vib. https://doi.org/10.1006/jsvi.1996.0578
Cremer L, Heckl M (1988) Structure-borne sound: structural vibrations and sound radiation at audio frequencies. Springer, Heidelberg
Aberg J (2006) On the experimental determination of damping of metals and calculation of thermal stresses in solidifying shells. Doctoral Thesis, Royal Institute of Technology, Stockholm
Stebbins RT, Dumont FD, Mock SE (1994) The inverted pendulum as a probe of anelasticity. Rev Sci Instrum 65(1):182–191. https://doi.org/10.1063/1.1144774
Ehrlich C, Schmidt A, Gaul L (2014) Microslip joint damping prediction using thin-layer elements. In: Dynamics of coupled structures, Bd. 1. Springer, Cham, S 239–244
Ozdemir AA, Gumussoy S (2017) Transfer function estimation in system identification toolbox via vector fitting. IFAC-PapersOnLine 50(1):6232–6237. https://doi.org/10.1016/j.ifacol.2017.08.1026
Ratcliffe CP (1998) Correcting a significant and consistent error in the modal damping obtained using transient vibration data (Technical report, Defense Technical Information Center of Colorado State University)
Franck M, Mönninghoff S, Butterweck D, Hameyer K (2021) Methodik zur Bestimmung von optimalen Messpunkten bei der strukturdynamischen Vermessung elektrischer Maschinen. Elektrotech Informationstech 138(6):431–437