Determination of minimum thickness of composite panels taking into account limits on stability and fatigue under postbuckling behavior
Tóm tắt
When designing the compressed thin composite skin of a multispar flap box of a small aircraft, its buckling due to compressive forces at loads below the operational level is admissible. This work considers smooth orthotropic rectangular panels loaded with longitudinal compressive strength. To determine the optimal parameters of the panels, a method based on a postbuckling state involving an analytical solution of geometrically nonlinear problems obtained by the Bubnov–Galerkin method was used. In this paper, methods for determining the minimum thickness of orthotropic panels, for which supercritical behavior is permissible when subjected to compressive forces, are developed. They include, firstly, the approaches using various strength criteria given the static loading, secondly, methods allowing for the variation of the width of the panel when considering two levels of loading: ensuring limitations of buckling at the first level of loading and static strength conditions in the case of geometrically nonlinear behavior at the second level of loading, and thirdly, methods taking into account the requirements of fatigue cycling. Here, also two levels of loading may be considered, at which stability and strength are ensured under postbuckling behavior, according to the parameters of fatigue loading and permissible stresses with respect to fatigue strength. These methods are reduced to solving analytical ratios with respect to the thickness shown on the example of hinge-supported composite panels. Since the obtained analytical relations are associated with the initial stage of postbuckling behavior, the paper provides an expression for compressive forces, at which the number of half-waves can be increased under geometrically nonlinear behavior. Of practical significance is the possibility of determining the optimal parameters of smooth orthotropic panels under static and fatigue loading at the early stages of design.
Tài liệu tham khảo
Degenhardt R, Castro S, Arbelo M, Zimmerman R, Khakimova R, Kling A (2014) Future structural stability design for composite space and airframe structures. Thin-Walled Struct 81:29–38. https://doi.org/10.1016/j.tws.2014.02.020
Advisory Circular 20–107B, U.S. Department of Transportation Federal Aviation Administration (2009). https://www.faa.gov/documentLibrary.
Falzon BG, Aliabadi MH (2008) Buckling and Postbuckling Structures: Experimental, Analytical and Numerical Studies. Imperial College London, UK. https://doi.org/10.1142/p506.
Faggiani A, Falzon BG (2018) Optimization of postbuckling-stiffened composite aerostructures buckling and postbuckling structures II experimental, analytical and numerical studies. Queen’s University Belfast. UK Chapter 8:253–284. https://doi.org/10.1142/9781786344335_0008
Vasiliev VV, Morozov EV (2018) Advanced Mechanics of Composite Materials and Structures. Elsevier, Amsterdam
Ni X, Prusty G, Hellier A (2016) Buckling and post-buckling of isotropic and composite stiffened panels: A review on optimisation (2000–2015). Trans. R. Inst. Nav. Archit. A: Int. J. Marit. Eng. 158:Part A3, pp A-251 – A-268. https://doi.org/10.5750/ijme.v158iA3.994.
Wu Z, Raju G, Weaver P (2016) Analysis and design for the moderately deep postbuckling behavior of composite plates. J Aircr 54:1–9. https://doi.org/10.2514/1.C033875
López C, Bacarreza O, Baldomir A, Hernandez S, Aliabadi MH (2017) Reliability-based design optimization of composite stiffened panels in post-buckling regime. Struct. Multidiscip. Optim. 55. https://doi.org/10.1007/s00158-016-1568-1.
Farokhi H, Bacarreza O, Aliabadi MH (2020) Probabilistic optimisation of mono-stringer composite stiffened panels in post-buckling regime. Struct. Multidiscip. Optim. 62. https://doi.org/10.1007/s00158-020-02565-9.
Madeo A, Groh RMJ, Zucco G, Weaver P, Zagari G, Zinno R (2016) Post-buckling analysis of variable-angle tow composite plates using Koiter’s approach and the finite element method. Thin-Walled Struct 110. https://doi.org/10.1016/j.tws.2016.10.012.
White S, Raju G, Weaver P (2014) Initial post-buckling of variable-stiffness curved panels. J Mech Phys Solids. 71. https://doi.org/10.1016/j.jmps.2014.07.003.
Quadros H, Hernandes J (2018) A lagrange parametrization for the design of variable stiffness laminates. Struct. Multidiscip. Optim 58. https://doi.org/10.1007/s00158-017-1882-2.
Wu Z, Raju G, Weaver P (2015) Framework for the buckling optimization of variable-angle tow composite plates. AIAA J 53:1–17. https://doi.org/10.2514/1.J054029
Liguori F, Zucco G, Madeo A, Magisano D, Leonetti L, Garcea G, Weaver P (2020) Koiter Method and Solid Shell Finite Elements for Postbuckling Optimisation of Variable Angle Tow Composite Structures. Proceedings of XXIV AIMETA Conference 2019. https://doi.org/10.1007/978-3-030-41057-5_139.
Hanatani Y, Nakada M, Miyano Y (2010) Validation of Fatigue Life Prediction Method under Variable Fatigue Loading for CFRP Laminates. Sci. Eng. Compos. 17. https://doi.org/10.1515/SECM.2010.17.4.261
Strizhius V (2016) Estimation of the Residual Fatigue Life of Laminated Composites Under a Multistage Cyclic Loading. Mech. Compos. Mater. 52. https://doi.org/10.1007/s11029-016-9611-2.
De Jonge JB, Schutz D, Lowak H, Schijve J (1973) A standardized load sequence for flight simulation tests on transport aircraft wing structures. LBF Bericht FB-106 (NLR 73029U).
Strizhius VE (2020) Calculation of equivalent stresses and equivalent fatigue test programs for elements of composite aircraft structures. Nauch vest Mosk gosudarstv tekh univ grazhd aviatsii 23(2):87–100. https://doi.org/10.26467/2079-0619-2020-23-2-87-100
Mitrofanov O (2002) Applied design of minimum weight composite wing panels taking into account skin post-buckling behavior. MAI Review 9(1):34
Mitrofanov O (2020) Designing load-bearing panels of aircraft structures for post-buckling state. Moscow, MAI. ISBN 978-5-4316-0757-8
Mitrofanov O, Osman M (2022) Designing of smooth composite panels providing stability and strength at postbuckling behavior. Mech compos mater 58, 1:21–22. https://doi.org/10.22364/mkm.58.1.02
Mitrofanov O, Osman M (2022) Design of thin orthotropic panels according to the postbuckling state under combined loading taking into account uniform heating. Aerospace Systems 5(1):29–36. https://doi.org/10.1007/s42401-021-00129-3