Determination of Mohr–Coulomb failure envelope, mechanical properties and UPV of commercial cement-lime mortar
Tóm tắt
Mortar in masonry structures can be subjected to both uniaxial and triaxial loading. Determining the mechanical properties and/or failure criteria of the commonly used mortar is necessary for the structural performance assessment of new and existing masonry buildings using non-destructive testing and/or finite element modelling methods. In this paper, the stress–strain behaviour of a commercially available cement-lime mortar is investigated under uniaxial and triaxial loading. The axial compressive strength, modulus of elasticity, Mohr–Coulomb failure envelopes of the mortar are determined over a range of conditions. Mortar specimens were prepared with a water to cementitious material ratio (w/cm) of 0.6–0.7 and were tested at curing ages of 3, 7, 14, and 28 days, under confining pressures of 0, 100, 250, 500 and 750 kPa. Ultrasonic pulse velocity (UPV) of the specimens were measured before the destructive testing. The results indicate that the influence of curing age and confining pressure on the axial compressive strength of the mortar can be predicted using proposed linear correlations between (i) The confining pressure and the axial compressive strength and (ii) The UPV and the axial compressive strength. From the test results, the strength parameters of the Mohr–Coulomb failure criterion were also determined. It is observed that cohesion is more sensitive to changes in curing age and w/cm than the friction angle, which varied between 32 and 33 degrees.
Tài liệu tham khảo
Noor-E-Khuda S, Albermani F (2019) Mechanical properties of clay masonry units: destructive and ultrasonic testing. Conctr Build Mater 219:111–120
Page A (2012) The evolution of the design and construction of masonry buildings in Australia. Gestão Tecnol Proj 7(2):27–34
McNary WS, Abrams DP (1985) Mechanics of masonry in compression. J Struct Eng (ASCE) 111(4):857–870
Khoo CL (1972) Failure criterion for brickwork in axial compression. Ph.D. Thesis, University of Edinburgh, Edinburg
Haach VG, Vasconcelos G, Lourenço PB (2011) Influence of aggregates grading and water/cement ratio in workability and hardened properties of mortars. Constr Build Mater 25:2980–2987
Asad M, Dhanasekar M, Zahra T, Thambiratnam D (2019) Characterisation of polymer cement mortar composites containing carbon fibre or auxetic fabric overlays and inserts under flexure. Constr Build Mater 224:863–879
de Oliveira TF, Beck MH, Escosteguy PV, Bortoluzzi EC, Modolo ML (2015) The effect of the substitution of hydrated lime with phyllite on mortar quality. Appl Clay Sci 105:113–117
Lanas J, Sirera R, Alvarez JI (2006) Study of the mechanical behavior of masonry repair lime-based mortars cured and exposed under different conditions. Cem Concr Res 36(5):961–970
Singh SB, Munjal P, Thammishetti N (2015) Role of water/cement ratio on strength development of cement mortar. J Build Eng 4:94–100
Binder E, Reihsner R, Yuan Y, Mang HA, Pichler BLA (2020) High-dynamic compressive and tensile strength of specimens made of cementitious materials. Cem Concr Res 129:105890
Noor-E-Khuda S (2021) Influence of wetting–drying cycles on compressive and flexural strength of cement mortar and CFRP-mortar bond strength. Constr Build Mater 271:121513
Zhou Q, Wang F, Zhu F, Yang X (2017) Stress–strain model for hollow concrete block masonry under uniaxial compression. Mater Struct 50(2):106
Assaad J, Harb J, Khayat K (2009) Use of triaxial compression test on mortars to evaluate formwork pressure of self-consolidating concrete. ACI Mater J 106(5):439–447
Yankelevsky DZ, Karinski YS, Zhutovsky S, Feldgun VR (2018) High-pressure uniaxial confined compression tests of mortars. Constr Build Mater 165:523–532
Yurtdas I, Burlion N, Skoczylas F (2004) Triaxial mechanical behaviour of mortar: Effects of drying. Cem Concr Res 34(7):1131–1143
Yurtdas I, Peng He, Burlion N, Skoczylas F (2006) Influences of water by cement ratio on mechanical properties of mortars submitted to drying. Cem Concr Res 36(7):1286–1293
Mohamad G, Fonseca FS, Roman HR, Vermeltfoort A and Rizzatti E (2015) Behavior of mortar under multi-axial stress. In: 12th North American Masonry conference, 17–20 May 2015, Denver, Colorado pp 1–12
Lourenço PB (1996) Computational strategies for masonry structures. Ph.D. Thesis, Delft University of Technology, Delft
Noor-E-Khuda S, Dhanasekar M, Thambiratnam DP (2016) Out-of-plane deformation and failure of masonry walls with various forms of reinforcement. Compos Struct 140:262–277
Noor-E-Khuda S (2021) An explicit finite-element modeling method for masonry walls using continuum shell element. J Archit Eng 27(4):04021040
Gabet T, Malécot Y, Daudeville L (2008) Triaxial behaviour of concrete under high stresses: influence of the loading path on compaction and limit states. Cem Concr Res 38(3):403–412
Toufigh V, Abyaneh MJ, Jafari K (2017) Study of behavior of concrete under axial and triaxial compression. ACI Mater J 114(4):619–629
Sfer D, Carol I, Gettu R, Etse G (2002) Study of the behavior of concrete under triaxial compression. J Eng Mech 128(2):156–163
Malecot Y, Zingg L, Briffaut M, Baroth J (2019) Influence of free water on concrete triaxial behavior: the effect of porosity. Cem Concr Res 120:207–216
Chen D, Yu X, Liu R, Li S, Zhang Y (2019) Triaxial mechanical behavior of early age concrete: experimental and modelling research. Cem Concr Res 115:433–444
Wang YB, Liew JY, Lee SC, Xiong DX (2016) Experimental study of ultra-high-strength concrete under triaxial compression. ACI Mater J. https://doi.org/10.14359/51688071
Hayen R, Schueremans L, Van Balen K, Van Gemert D (2001) Triaxial testing of historic masonry, test set-up and first results. WIT Trans Built Environ 55:1–10
Atkinson RH, Noland JL, Abrams DP, McNary S (1985) Deformation failure theory for stack-bond brick masonry prisms in compression. In: Mathys JH, Borchelt JG (eds) Proceedings of 3rd North American Masonry conference, Arlington
Sbartaï ZM, Breysse D, Larget M, Balayssac JP (2012) Combining NDT techniques for improved evaluation of concrete properties. Cem Concr Compos 34(6):725–733
Sharma S, Mukherjee A (2015) Monitoring freshly poured concrete using ultrasonic waves guided through reinforcing bars. Cem Concr Compos 55:337–347
Carette J, Staquet S (2016) Monitoring and modelling the early age and hardening behaviour of eco-concrete through continuous non-destructive measurements: part II. Mech Behav Cem Concr Compos 73:1–9
Noor-E-Khuda S, Albermani F (2019) Flexural strength of weathered granites under wetting–drying cycles: implications to steel structures. Adv Steel Constr 15(3):225–231
Noor-E-Khuda S, Albermani F, Veidt M (2017) Flexural strength of weathered granites: influence of freeze and thaw cycles. Constr Build Mater 156:891–901
AS 3700 (Australian Standard) (2018) Australian Standard of Masonry Structures. Sydney
Think Brick Australia, Manual To Construction Guidelines for Clay Masonry (2020) https://www.thinkbrick.com.au/Technical/Manuals/DownloadManual/12?ManualName=Manual%2010-Construction%20guidelines.pdf. Accessed 20 July 2020
Australian Standard (2014) Methods of testing concrete; Preparation of concrete mixes in the laboratory. AS 1012.2: 2014
Australian Standard (2014) Methods of testing concrete; method for making and curing concrete. AS 1012.8.1: 2014
AS 2350 (Australian Standard) (2016) Methods of testing Portland, blended and masonry cements. Sydney
Binda L, de Vekey B, Acharhabi A, Baronio G, Bekker P, Borchelt G, Groot C (1998) RILEM TC 127-MS: tests for masonry materials and structures. Mater Struct 31(205):2–19
Breysse D (2012) Nondestructive evaluation of concrete strength: an historical review and a new perspective by combining NDT methods. Constr Build Mater 33:139–163
Nakamura H, Nanri T, Miura T, Roy S (2018) Experimental investigation of compressive strength and compressive fracture energy of longitudinally cracked concrete. Cement Concr Compos 93:1–18
Pluijm RVD (1999) Out-of-plane bending of masonry, behavior and strength. Ph.D. Thesis, Eindhoven University of Technology, Eindhoven
Benedetti A, Pelà L and Aprile A (2008) Masonry properties determination via splitting tests on cores with a rotated mortar layer. In: Proceedings of 8th international seminar on structural masonry, Istanbul
Vu XH, Malecot Y, Daudeville L, Buzaud E (2009) Experimental analysis of concrete behavior under high confinement: effect of the saturation ratio. Int J Solids Struct 46(5):1105–1120