Design and Evaluation of a 100 kN m Multi-function Torque Standard Machine
Tóm tắt
This paper presents the design and evaluation of a Multi-function torque standard machine (MFTSM) capable of calibrating hydraulic torque wrenches, torque multipliers either concentric or nonconcentric up to 100 kN m, and torque transducers with regular or irregular bases up to 2.5 kN m, in clockwise and anticlockwise directions. The machine’s performance was evaluated through a series of calibrations and comparisons that revealed good consistency, as the
Từ khóa
Tài liệu tham khảo
C. Schlegel, D. Röske, D. Mauersberger and P. Hohmann, Metrological characterization of a 20 N·m torque calibration standard machine at (PTB), Germany. J. Phys. Conf. Ser., 1065 (2018) 42026. https://doi.org/10.1088/1742-6596/1065/4/042026.
D. Röske, Metrological characterization of a 1 N m torque standard machine at (PTB), Germany. Metrologia, 51(1) (2014) 87–96. https://doi.org/10.1088/0026-1394/51/1/87.
D. Adolf, K. Mauersberger, D. Peschel, Specifications and uncertainty of measurement of the PTB’s 1 kNm torque standard machine. In Proceedings of the 14th IMEKO TC3 conference, (1995) pp. 174–176.
A. Pusa, Torque calibration in Finland, (1996).
K. Ohgushi, T. Ota, K. Ueda, and E. Furuta, Design and development of 20 kN m deadweight torque standard machine. In 18th IMEKO TC3 conference force, mass torque, (2002) pp. 52–57.
T. Sanponpute, P. Chantaraksa, N. Saenkhum, and N. Arksonnarong, Suspended-fulcrum torque standard machine. In 19th IMEKO world congress, (2009) pp. 343–346.
A. Pusa, D. Röske, and M. Sachs, Comparison measurement of MIKES_RAUTE 20 kN·m torque reference device with PTB. In Proceedings of the 19th IMEKO conference, (2005) pp. 1–6.
K. M. Khaled, G. Aggag, A. E. Abuelezz, and M. G. Elsherbiny, Mechanical design of NIS new reference torque standard machine. In IMEKO TC3, TC5 and TC22 conferences, (2010) pp. 109–114.
K. M. Khaled, G. Aggag, A. E. Abuelezz, and M. G. Elsherbiny, Performance evaluation of nis new reference torque standard machine. In IMEKO TC3, TC5 and TC22 conferences, (2010) pp. 269–272.
D. Peschel, Proposal for the design of torque standard machines using the principle of a component system. In Proceedings of the 15th IMEKO TC3 conference, (1996) pp. 251–254.
D. Peschel, D. Mauersberger, D. Schwind, and U. Kolwinski, The New 1.1 MNm torque standard machine of The PTB Braunschweig/Germany. In Proceedings of 19th international IMEKO conference, (2005) pp. 1–7.
H. J. Fraiss, L. Stenner, and D. Röske, Development of a new 400 kN·m torque standard machine. In XXI IMEKO world congress “measurement in research and industry, (2015) pp. 196–200.
H. Kahmann, C. Schlegel, R. Kumme, K. Geva, P. Wortmann, and S. Augustat, Principle and design of a 5 MN·m torque standard machine. In IMEKO TC3, TC5 and TC22 international conference, (2017) pp. 114–117.
G. Foyer and H. Kahmann, Design of a force lever system to allow traceable calibration of MN·m torque in nacelle test benches. In Sensors and measuring systems; 19th ITG/GMA-symposium, (2018), vol. 2018, pp. 127–130.
F. Härtig, J. Hornig, H. Kahmann, K. Kniel, H. Müller, and C. Schlegel, Metrological competence center for wind energy. (2018) https://doi.org/10.1088/1742-6596/1065/4/042053.
C.A. Sanchez, B.M. Wood, R.G. Green, J.O. Liard and D. Inglis, A determination of Planck’s constant using the NRC watt balance. Metrologia, 51(2) (2014) S5–S14. https://doi.org/10.1088/0026-1394/51/2/s5.
D. Kim et al., Design of the KRISS watt balance. Metrologia, 51(2) (2014) S96–S100. https://doi.org/10.1088/0026-1394/51/2/s96.
A. Nishino, K. Ueda and K. Fujii, Design of a new torque standard machine based on a torque generation method using electromagnetic force. Meas. Sci. Technol., 28(2) (2016) 25005. https://doi.org/10.1088/1361-6501/28/2/025005.
M. Kim, Design of a new dual-mode torque standard machine that operates on the principle of the kibble balance. In 2020 Conference on precision electromagnetic measurements (CPEM), (2020) pp. 1–2. https://doi.org/10.1109/CPEM49742.2020.9191819.
M. Kim, Design of a new dual-mode torque standard machine using the principle of the kibble balance. IEEE Trans. Instrum. Meas., 70 (2021) 1–7. https://doi.org/10.1109/TIM.2021.3060574.
A. Nishino and K. Fujii, Calibration of a torque measuring device using an electromagnetic force torque standard machine. Measurement, 147 (2019) 106821. https://doi.org/10.1016/j.measurement.2019.07.049.
F. Meng, J.P. Jiao, Z.M. Zhang and D.L. Zhang, Various torque tools calibration at NIM. Meas. Sensors, 18 (2021) 100177. https://doi.org/10.1016/j.measen.2021.100177.
F. Meng, Y. Zhang, Z. Zhang, and T. Li, A new multifunction torque standard machine at NIM. In 20th IMEKO World Congress: Metrology for green growth, (2012) vol. 1, pp. 160–163.