Coupled influence of strain rate and heterogeneous fibre orientation on the mechanical behaviour of short-glass-fibre reinforced polypropylene

Advani, 1987, The use of tensors to describe and predict fiber orientation in short fiber composites, J. Rheol., 31, 751, 10.1122/1.549945

Arbelaiz, 2005, Mechanical properties of short flax fibre bundle/polypropylene composites: Influence of matrix/fibre modification, fibre content, water uptake and recycling, Composites Sci. Technol., 65, 1582, 10.1016/j.compscitech.2005.01.008

Awal, 2011, Interfacial studies of natural fibre/polypropylene composites using single fibre fragmentation test (SFFT), Composites, 42, 50, 10.1016/j.compositesa.2010.10.007

Balieu, 2013, A fully coupled elastoviscoplastic damage model at finite strains for mineral filled semi-crystalline polymer, Int. J. Plasticity, 51, 241, 10.1016/j.ijplas.2013.05.002

Bernasconi, 2007, Effect of fibre orientation on the fatigue behaviour of a short glass fibre reinforced polyamide-6, Int. J. Fatigue, 29, 199, 10.1016/j.ijfatigue.2006.04.001

Bowyer, 1972, On the re-inforcement of thermoplastics by imperfectly aligned discontinuous fibres, J. Mater. Sci., 7, 1315, 10.1007/BF00550698

Charlet, 2011, Mechanical properties of interfaces within a flax bundle - Part I: Experimental analysis, Int. J. Adhesion Adhesives, 31, 875, 10.1016/j.ijadhadh.2011.08.008

Dasari, 2003, Microstructural evolution during tensile deformation of polypropylenes, Mater. Sci. Eng. A, 351, 200, 10.1016/S0921-5093(02)00854-7

Doghri, 2006, Micromechanics of inelastic composites with misaligned inclusions: Numerical treatment of orientation, Comput. Methods Appl. Mech. Eng., 195, 1387, 10.1016/j.cma.2005.05.041

Epee, 2011, Constitutive model for a semi-cristalline polymer under dynamic loading, Int. J. Solids Struct., 48, 1590, 10.1016/j.ijsolstr.2011.02.009

Fitoussi, 2013, Effect of matrix behavior on the damage of ethylene-propylene glass fiber reinforced composite subjected to high strain rate tension, Composites, 45, 1181, 10.1016/j.compositesb.2012.06.011

Friedrich, 1985, Microstructural efficiency and fracture toughness of short fiber/thermoplastic matrix composites, Composite Sci. Technol., 22, 43, 10.1016/0266-3538(85)90090-9

Hull, 1996

Kammoun, 2011, First pseudo-grain failure model for inelastic composites with misaligned short fibers, Composites, 42, 1892, 10.1016/j.compositesa.2011.08.013

Miled, 2013, Micromechanical modeling of coupled viscoelastic–viscoplastic composites based on an incrementally affine formulation, Int. J. Solids Struct., 50, 1755, 10.1016/j.ijsolstr.2013.02.004

Modniks, 2013, Modeling the non-linear deformation of a short-flax-fiber-reinforced polymer composite by orientation averaging, Composites, 54, 188, 10.1016/j.compositesb.2013.04.058

Mouhmid, 2006, A study of the mechanical behaviour of a glass fibre reinforced polyamide 6,6: Experimental investigation, Polymer Testing, 25, 544, 10.1016/j.polymertesting.2006.03.008

Notta-Cuvier, 2013, An efficient modelling of inelastic composites with misaligned short fibres, Int. J. Solids Struct., 50, 2857, 10.1016/j.ijsolstr.2013.04.031

Notta-Cuvier, 2014, Damage of short-fibre reinforced materials with anisotropy induced by complex fibres orientations, Mech. Mater., 68, 193, 10.1016/j.mechmat.2013.09.011

Notta-Cuvier, 2015, Modelling of progressive fibre/matrix debonding in short-fibre reinforced composites up to failure, Int. J. Solids Struct., 66, 140, 10.1016/j.ijsolstr.2015.03.034

Notta-Cuvier, 2015, Impact of natural variability of flax fibres properties on mechanical behaviour of short-flax-fibre-reinforced polypropylene, J. Mater. Sci., 51, 2911, 10.1007/s10853-015-9599-3

Placet, 2014, Nonlinear tensile behaviour of elementary hemp fibres. Part I: Investigation of the possible origins using repeated progressive loading with in situ microscopic observations, Composites, 56, 319, 10.1016/j.compositesa.2012.11.019

Pracella, 2006, Functionalization, compatibilization and properties of polypropylene composites with Hemp fibres, Composites Sci. Technol., 66, 2218, 10.1016/j.compscitech.2005.12.006

Reder, 2003, Non-contacting strain measurements of ceramic and carbon single fibres by using the laser-speckle method, Composites, 34, 1029, 10.1016/S1359-835X(03)00240-9

Reis, 2013, Tensile behaviour of glass fibre reinforced polyurethane at different strain rates, Mater. Des., 49, 192, 10.1016/j.matdes.2013.01.065

Sato, 1991, Microfailure behaviour of randomly dispersed short fibre reinforced thermoplastic composites obtained by direct SEM observation, J. Mater. Sci., 26, 3891, 10.1007/BF01184987

Schindelin, 2012, Fiji: an open-source platform for biological-image analysis, Nat. Methods, 9, 676, 10.1038/nmeth.2019

Schoßig, 2008, Mechanical behavior of glass-fiber reinforced thermoplastic materials under high strain rates, Polym. Testing, 27, 893, 10.1016/j.polymertesting.2008.07.006

Sutton, 2009, Image correlation for shape, motion and deformation measurements

Tiwari, 2012, Optimization of surface treatment to enhance fiber-matrix interface and performance of composites, Wear 274-275, 326, 10.1016/j.wear.2011.09.014

Vincent, 1997, Fibre orientation calculation in injection moulding of reinforced thermoplastics, J. Non-Newtonian Fluid Mech., 73, 317, 10.1016/S0377-0257(97)00048-7

Yue, 1995, Assessment of fibre–matrix adhesion and interfacial properties using the pull-out test, Int. J. Adhesion Adhesives, 15, 73, 10.1016/0143-7496(95)98740-D

Zeng, 2010, A constitutive model for semi-crystalline polymers at high temperature and finite plastic strain: Application to PA6 and PE biaxial stretching, Mech. Mater., 42, 686, 10.1016/j.mechmat.2010.04.006

Zhandarov, 2014, An alternative method of determining the local interfacial shear strength from force-displacement curves in the pull-out and microbond tests, Int. J.Adhesion Adhesives, 55, 37, 10.1016/j.ijadhadh.2014.07.006