Computational Investigation of Interface Stresses in Duplex Structure Stainless Steels
Tóm tắt
Duplex structural stainless steels (DP) are highly corrosion-resistant with austenite (γ)-ferrite (δ) compositions and processing routes. These DP steels are used in chemical, petrochemical, marine, power generation, and nuclear industries due to their unique properties. Experimental data of 2D slices obtained from optical micrography were used in a multilevel finite element analysis to investigate the interface stresses between the two phases of DP material. Level #1 (macro-level) finite element analysis involves homogenizing the 2D slices based on their representative constituent properties to identify high-stress regions. Level #2 (micro-level) finite element analysis was conducted with representative austenite/ferrite microstructure identified from level #1 analysis. The results from finite element simulations from both macro- and micro-levels revealed that interface stresses are affected by the phase’s microstructure distributions. Micro-level analysis revealed maximum interface stress is much higher than macro-level analysis. It was also found that stress localization occurred at the ferrite/austenite interfaces based on their distributions.
Tài liệu tham khảo
K.H. Lo, C.H. Shek, and J.K.L. Lai, Recent Developments in Stainless Steels, Materials Science and Engineering: R: Reports, 2009, 65(4–6), p 39–104
I. Alvarez-Armas and S. Degallaix-Moreuil, Duplex Stainless Steels, Wiley, Hoboken, 2013, p 1–437
M. Okayasu and D. Ishida, Effect of Microstructural Characteristics on Mechanical Properties of Austenitic, Ferritic, and γ-α Duplex Stainless Steels, Metall. Mater. Trans. A, 2019, 50(3), p 1380–1388
C.C. Tasan et al., An Overview of Dual-Phase Steels: Advances in Microstructure-Oriented Processing and Micromechanically Guided Design, Annu. Rev. Mater. Res., 2015, 45(1), p 391–431
S.K. Paul, Real Microstructure Based Micromechanical Model to Simulate Microstructural Level Deformation Behavior and Failure Initiation in DP 590 Steel, Mater. Des., 2013, 44, p 397–406
J. Bouquerel, K. Verbeken, and B. Decooman, Microstructure-Based Model for the Static Mechanical Behaviour of Multiphase Steels, 2006, 54(6), p 1443–1456
G. Chai, Fatigue Behaviour of Duplex Stainless Steels in the Very High Cycle Regime, Int. J. Fatigue, 2006, 28(11), p 1611–1617
A. Mateo et al., Anisotropy Effects on the Fatigue Behaviour of Rolled Duplex Stainless Steels, Int. J. Fatigue, 2003, 25(6), p 481–488
W.B. Hutchinson, K. Ushioda, and G. Runnsjö, Anisotropy of Tensile Behaviour in a Duplex Stainless Steel Sheet, Mater. Sci. Technol., 1985, 1(9), p 728–736
L. Jinlong et al., Effect of Ultrafine Grain on Tensile Behaviour and Corrosion Resistance of the Duplex Stainless Steel, Mater. Sci. Eng., C, 2016, 62, p 558–563
J.-Y. Kang, H.-C. Lee, and S.H. Han, Effect of Al and Mo on the Textures and Microstructures of Dual Phase Steels, 2011, 530, p 183–190
A.P. Pierman et al., The Influence of Microstructure and Composition on the Plastic Behaviour of Dual-Phase Steels, Acta Mater., 2014, 73, p 298–311
M. Erdogan, Effect of Austenite Dispersion on Phase Transformation in Dual Phase Steel, Scripta Mater., 2003, 48(5), p 501–506
D. Gerbig et al., Analysis and Design of Dual-Phase Steel Microstructure for Enhanced Ductile Fracture Resistance, Int. J. Fract., 2017, 209(1–2), p 3–26
D. Gerbig et al., Analysis and Design of Dual-Phase Steel Microstructure for Enhanced Ductile Fracture Resistance, Int. J. Fract., 2018, 209(1–2), p 3–26
V. Tvergaard and V. Tvergaard, Influence of Voids on Shear Band Instabilities under Plane Strain Conditions, Int. J. Fract., 1981, 17(4), p 389–407
D.A. Korzekwa et al., A Consideration of Models Describing the Strength and Ductility of Dual-Phase Steels, Scr. Metall., 1980, 14(9), p 1023–1028
F.M. Al-Abbasi and J.A. Nemes, Micromechanical Modeling of Dual Phase Steels, Int. J. Mech. Sci., 2003, 45(9), p 1449–1465
F.M. Al-Abbasi and J.A. Nemes, Characterizing DP-Steels Using Micromechanical Modeling of Cells, Comput. Mater. Sci., 2007, 39(2), p 402–415
N.H. Abid, R.K. Abu Al-Rub, and A.N. Palazotto, Micromechanical Finite Element Analysis of the Effects of Martensite Morphology on the Overall Mechanical Behavior of Dual Phase Steel, Int. J. Solids Struct., 2017, 104-105, p 8–24
M. Amirmaleki et al., 3D Micromechanical Modeling of Dual Phase Steels Using the Representative Volume Element Method, Mech. Mater., 2016, 101, p 27–39
S. Ankem, H. Margolin, C.A. Greene, B.W. Neuberger, and P.G. Oberson, Mechanical Properties of Alloys Consisting of Two Ductile Phases, Prog. Mater Sci., 2006, 51, p 632–709
K.S. Choi, A. Soulami, W.N. Liu, X. Sun, and M.A. Khalel, Influence of Various Material Design Parameters on Deformation Behaviors of TRIP Steels, Comput. Mater. Sci., 2010, 2, p 720–730
E.Y. Guo, S.S. Singh, H. Xie, J.J. Williams, T. Jing, and N. Chawala, Microstructure Based Modeling of Deformation in Steels Based on Constitutive Relationships from Micropillar Compression, Steel Res. Int., 2014, 85(6), p 946–953
P. Tao, J. Gong, Y. Wang, Y. Jiang, Y. Li, and W. Cen, Characterization on Stress-Strain Behavior of Ferrite and Austenite in a 2205 Duplex Stainless Steel Based on Nanoindentation and Finite Element Method, Results Phys., 2018, 11, p 377–384
S.C. Schwarm, R.P. Kollie, E. Aydogan, S. Mburu, and S. Ankem, Characterization of Phase Properties and Deformation in Ferritic-Austenitic Duplex Stainless Steels by Nanoindentation and Finite Element Method, Mater. Sci. Eng., A, 2017, 680, p 359–367
Q. Zhang, K. Zhu, A.S.S. Singaravelu, W. Sun, T. Jing, and N. Chawla, Three-Dimensional (3D) Microstructure-Based Modeling of a Thermally-Aged Cast Duplex Stainless Steel Based on X-ray Microtomography, Nanoindentation and Micropillar Compression. Metals, 2019, 9(6), p 668