Compressive strength, flexural strength and thermal conductivity of autoclaved concrete block made using bottom ash as cement replacement materials

Kurama H, Topcu IB, Karakurt C. Properties of the autoclaved aerated concrete production from coal bottom ash. J Mater Process Tech 2008/2009;209:767–73. Short, 1963 Mindess S, Young JF, Darwin D. Concrete. 2nd ed.; 2002. Yazici, 2007, The effect of curing conditions on compressive strength of ultra high strength concrete with high volume mineral admixtures, Build Environ, 42, 2083, 10.1016/j.buildenv.2006.03.013 Chindaprasirt, 2011, Shrinkage behavior of structural foam lightweight concrete containing glycol compounds and fly ash, Mater Des, 32, 723, 10.1016/j.matdes.2010.07.036 Tanyildizi, 2009, Fuzzy logic model for prediction of mechanical properties of lightweight concrete exposed to high temperature, Mater Des, 30, 2205, 10.1016/j.matdes.2008.08.030 Bai, 2005, Strength and drying shrinkage properties of concrete containing furnace bottom ash as fine aggregate, Constr Build Mater, 19, 691, 10.1016/j.conbuildmat.2005.02.021 Ozkan, 2007, Strength properties of concrete incorporating coal bottom ash and granulated blast furnace slag, Waste Manage, 27, 161, 10.1016/j.wasman.2006.01.006 Yuksel, 2007, Durability of concrete incorporating non-ground blast furnace slag and bottom ash as fine aggregate, Build Environ, 42, 2651, 10.1016/j.buildenv.2006.07.003 ASTM C 33-02. Standard specification for concrete aggregates. Philadelphia: American Society for Testing and Materials; 2002. Cheriaf, 1999, Pozzolanic properties of pulverized coal combustion bottom ash, Cem Concr Res, 29, 1387, 10.1016/S0008-8846(99)00098-8 ASTM C495. Standard test method for compressive strength of lightweight insulating concrete. Philadelphia: American Society for Testing and Materials; 2002. ASTM C138-92. Standard test method for unit weight, yield, and air content (gravimetric) of concrete. Philadelphia: American Society for Testing and Materials; 2002. ASTM D 5930-01. Standard test method for thermal conductivity of plastics by means of a transient line-source technique. Philadelphia: American Society for Testing and Materials; 2002. ASTM C 348-97. Standard test method for flexural strength of hydraulic-cement mortars. Philadelphia: American Society for Testing and Materials; 2002. Meller, 2009, The mineralogy of the CaO–Al2O3–SiO2–H2O (CASH) hydroceramic system from 200 to 350°C, Cem Concr Res, 39, 45, 10.1016/j.cemconres.2008.10.002 Topcu, 2007, Properties of autoclaved lightweight aggregate concrete, Build Environ, 42, 4108, 10.1016/j.buildenv.2006.11.024 Corinaldesi, 2011, Mechanical behaviour and thermal conductivity of mortars containing waste rubber particles, Mater Des, 32, 1646, 10.1016/j.matdes.2010.10.013 Albayrak, 2007, Influence of zeolite additive on properties of autoclaved aerated concrete, Build Environ, 42, 3161, 10.1016/j.buildenv.2006.08.003 Demirboga, 2003, Influence of mineral admixtures on thermal conductivity and compressive strength of mortar, Energy build, 35, 189, 10.1016/S0378-7788(02)00052-X Demirboga, 2007, Thermal conductivity and compressive strength of concrete incorporation with mineral admixtures, Build Environ, 42, 2467, 10.1016/j.buildenv.2006.06.010 Demirboga, 2003, The effects of expanded perlite aggregate, silica fume, fly ash on the thermal conductivity of lightweight concrete, Cem Concr Res., 33, 723, 10.1016/S0008-8846(02)01032-3 Blanco, 2000, Characteristic and properties of lightweight concrete manufactured with cenospheres, Cem Concr Res, 30, 1715, 10.1016/S0008-8846(00)00357-4 Unal, 2007, Investigation of properties of low-strength lightweight concrete for thermal insulation, Build Environ, 42, 584, 10.1016/j.buildenv.2005.09.024 Taylor, 1997