Circular Simple Shear Extrusion as an Alternative to Simple Shear Extrusion Technique
Iranian Journal of Science and Technology, Transactions of Mechanical Engineering - Tập 44 - Trang 193-201 - 2018
Tóm tắt
Recently, simple shear extrusion (SSE) was introduced to fabricate ultra-fine-grained materials. It was designed for billets with square cross sections and was investigated well previously. This study aims to introduce a new alternative design of simple shear extrusion process with a circular cross section, which is named circular simple shear extrusion (CSSE). Therefore, the finite element analysis is applied for investigating the deformation behavior during the CSSE process. The results show that the CSSE process fills the die with less back-pressure and the strain values are closer to theoretical ones in comparison with SSE with a square cross section. Moreover, this new alternative is needed to lower the extrusion pressure compared to SSE with a square cross section. In addition, the contact pressure and the maximum principal stress in a die with a circular cross section are lower in comparison with the square one which leads to a longer service life of CSSE’s die. Hence, this new geometry will provide more potential in terms of industrial applications.
Tài liệu tham khảo
Akhtar SS, Arif AFM (2009) Fatigue failure of extrusion dies: effect of process parameters and design features on die life. J Fail Anal Prev 10(1):38–49. https://doi.org/10.1007/s11668-009-9304-4
Archard JF (1953) Contact and rubbing of flat surfaces. J Appl Phys 24(8):981–988. https://doi.org/10.1063/1.1721448
Bagherpour E, Reihanian M, Ebrahimi R (2012a) On the capability of severe plastic deformation of twining induced plasticity (TWIP) steel. Mater Des 36:391–395. https://doi.org/10.1016/j.matdes.2011.11.055
Bagherpour E, Reihanian M, Ebrahimi R (2012b) Processing twining induced plasticity steel through simple shear extrusion. Mater Des 40:262–267. https://doi.org/10.1016/j.matdes.2012.03.055
Bagherpour E, Qods F, Ebrahimi R (2014) Effect of geometric parameters on deformation behavior of simple shear extrusion. IOP Conf Ser Mater Sci Eng 63:012046. https://doi.org/10.1088/1757-899x/63/1/012046
Bagherpour E, Ebrahimi R, Qods F (2015) An analytical approach for simple shear extrusion process with a linear die profile. Mater Des 83:368–376. https://doi.org/10.1016/j.matdes.2015.06.023
Bagherpour E, Qods F, Ebrahimi R, Miyamoto H (2016a) Microstructure evolution of pure copper during a single pass of simple shear extrusion (SSE): role of shear reversal. Mater Sci Eng A 666:324–338. https://doi.org/10.1016/j.msea.2016.04.080
Bagherpour E, Qods F, Ebrahimi R, Miyamoto H (2016b) Texture changes during simple shear extrusion (SSE) processing of pure copper. Mater Trans 57:1386–1391. https://doi.org/10.2320/matertrans.mh201501
Bagherpour E, Qods F, Ebrahimi R, Miyamoto H (2016c) Microstructure quantification of ultrafine grained pure copper fabricated by simple shear extrusion (SSE) technique. Mater Sci Eng A 674:221–231. https://doi.org/10.1016/j.msea.2016.08.001
Bagherpour E, Qods F, Ebrahimi R, Miyamoto H (2017) Nanostructured pure copper fabricated by simple shear extrusion (SSE): a correlation between microstructure and tensile properties. Mater Sci Eng A 679:465–475. https://doi.org/10.1016/j.msea.2016.10.068
Beygelzimer Y, Prilepo D, Kulagin R, Grishaev V, Abramova O, Varyukhin V, Kulakov M (2011) Planar twist extrusion versus twist extrusion. J Mater Process Technol 211(3):522–529. https://doi.org/10.1016/j.jmatprotec.2010.11.006
Chen Y, Wang Q, Lin J, Zhang L, Zhai C (2007) Fabrication of bulk UFG magnesium alloys by cyclic extrusion compression. J Mater Sci 42(17):7601–7603. https://doi.org/10.1007/s10853-007-1889-y
Ebrahimi R, Najafizadeh A (2004) A new method for evaluation of friction in bulk metal forming. J Mater Process Technol 152(2):136–143. https://doi.org/10.1016/j.jmatprotec.2004.03.029
Ebrahimi R, Pardis N (2009) Determination of strain-hardening exponent using double compression test. Mater Sci Eng A 518(1–2):56–60. https://doi.org/10.1016/j.msea.2009.04.050
Ebrahimi R, Rezvani A, Bagherpour E (2018) Circular simple shear extrusion as an alternative to simple shear extrusion technique for producing bulk nanostructured materials. Proc Manuf 15:1502–1508
Farzad H, Ebrahimi R (2016) Die profile optimization of rectangular cross section extrusion in plane strain condition using upper bound analysis method and simulated annealing algorithm. J Manuf Sci Eng 139(2):021006. https://doi.org/10.1115/1.4034336
Figueiredo RB, de Faria GCV, Cetlin PR, Langdon TG (2012) Three-dimensional analysis of plastic flow during high-pressure torsion. J Mater Sci 48(13):4524–4532. https://doi.org/10.1007/s10853-012-6979-9
Furukawa M, Horita Z, Nemoto M, Langdon TG (2001) Review: processing of metals by equal-channel angular pressing. J Mater Sci 36(12):2835–2843. https://doi.org/10.1023/A:1017932417043
Kang F, Wang JT, Su YL, Xia KN (2007) Finite element analysis of the effect of back pressure during equal channel angular pressing. J Mater Sci 42(5):1491–1500. https://doi.org/10.1007/s10853-006-0762-8
Kim JG, Latypov M, Pardis N, Beygelzimer YE, Kim HS (2015) Finite element analysis of the plastic deformation in tandem process of simple shear extrusion and twist extrusion. Mater Des 83:858–865. https://doi.org/10.1016/j.matdes.2015.06.034
Latypov MI, Alexandrov IV, Beygelzimer YE, Lee S, Kim HS (2012) Finite element analysis of plastic deformation in twist extrusion. Comput Mater Sci 60:194–200. https://doi.org/10.1016/j.commatsci.2012.03.035
Latypov MI, Beygelzimer Y, Kim HS (2013) Comparative analysis of two twist-based SPD processes: elliptical cross-section spiral equal-channel extrusion vs. twist extrusion. Mater Trans 54:1587–1591. https://doi.org/10.2320/matertrans.mh201315
Lee DJ, Kim HS (2014) Finite element analysis for the geometry effect on strain inhomogeneity during high-pressure torsion. J Mater Sci 49(19):6620–6628. https://doi.org/10.1007/s10853-014-8283-3
Lin J, Wang Q, Peng L, Roven HJ (2008) Study on deformation behavior and strain homogeneity during cyclic extrusion and compression. J Mater Sci 43(21):6920–6924. https://doi.org/10.1007/s10853-008-2994-2
Molaei SH, Shahbaz M, Ebrahimi R (2014) The relationship between constant friction factor and coefficient of friction in metal forming using finite element analysis. Iran J Mater Form 1(2):14–22. https://doi.org/10.22099/IJMF.2014.2290
Molaei S, Ebrahimi R, Abbasi Z (2016) Upper bound analysis of barrel compression test using a new velocity field. Iran J Sci Technol Trans Mech Eng 40(1):1–10. https://doi.org/10.1007/s40997-016-0003-y
Pardis N, Ebrahimi R (2009) Deformation behavior in simple shear extrusion (SSE) as a new severe plastic deformation technique. Mater Sci Eng A 527(1–2):355–360. https://doi.org/10.1016/j.msea.2009.08.051
Pardis N, Ebrahimi R (2010) Different processing routes for deformation via simple shear extrusion (SSE). Mater Sci Eng A 527(23):6153–6156. https://doi.org/10.1016/j.msea.2010.06.028
Pardis N, Talebanpour B, Ebrahimi R, Zomorodian S (2011) Cyclic expansion-extrusion (CEE): a modified counterpart of cyclic extrusion-compression (CEC). Mater Sci Eng A 528(25–26):7537–7540. https://doi.org/10.1016/j.msea.2011.06.059
Roostaei AA, Zarei-Hanzaki A, Parsa MH, Fatemi-Varzaneh SM (2010) An analysis to plastic deformation behavior of AZ31 alloys during accumulative roll bonding process. J Mater Sci 45(16):4494–4500. https://doi.org/10.1007/s10853-010-4540-2
Saito Y, Tsuji N, Utsunomiya H, Sakai T, Hong RG (1998) Ultra-fine grained bulk aluminum produced by accumulative roll-bonding (ARB) process. Scr Mater 39(9):1221–1227. https://doi.org/10.1016/s1359-6462(98)00302-9
Segal VM (1995) Materials processing by simple shear. Mater Sci Eng A 197(2):157–164. https://doi.org/10.1016/0921-5093(95)09705-8
Sheikh H, Ebrahimi R (2016) Investigation on texture evolution during cyclic expansion–extrusion (CEE) technique using crystal plasticity finite element modeling. J Mater Sci 51(22):10178–10190. https://doi.org/10.1007/s10853-016-0245-5
Terada D, Inoue S, Tsuji N (2007) Microstructure and mechanical properties of commercial purity titanium severely deformed by ARB process. J Mater Sci 42(5):1673–1681. https://doi.org/10.1007/s10853-006-0909-7
Tork NB, Pardis N, Ebrahimi R (2013) Investigation on the feasibility of room temperature plastic deformation of pure magnesium by simple shear extrusion process. Mater Sci Eng A 560:34–39. https://doi.org/10.1016/j.msea.2012.08.085
Valiev RZ (2007) The new trends in fabrication of bulk nanostructured materials by SPD processing. J Mater Sci 42(5):1483–1490. https://doi.org/10.1007/s10853-006-1281-3
Wang C, Li F, Li Q, Li J, Wang L, Dong J (2013a) A novel severe plastic deformation method for fabricating ultrafine grained pure copper. Mater Des 43:492–498. https://doi.org/10.1016/j.matdes.2012.07.047
Wang C, Li F, Lu H et al (2013b) Deformation analysis of elliptical cross-section spiral equal channel extrusion technique. Rare Metal Mater Eng 42:679–683. https://doi.org/10.1016/s1875-5372(13)60055-7
Yoon EY, Yoo JH, Yoon SC, Kim YK, Baik SC, Kim HS (2010) Analyses of route Bc equal channel angular pressing and post-equal channel angular pressing behavior by the finite element method. J Mater Sci 45(17):4682–4688. https://doi.org/10.1007/s10853-010-4469-5
Zhu Y, Valiev RZ, Langdon TG, Tsuji N, Lu K (2010) Processing of nanostructured metals and alloys via plastic deformation. MRS Bull 35:977–981. https://doi.org/10.1557/mrs2010.702