Capacity models for shear strength of exterior joints in RC frames: state-of-the-art and synoptic examination
Tóm tắt
Damage observed in existing structures after recent earthquake events pointed out the key importance of beam-to-column joints in influencing the global response of reinforced concrete structures. In the last two decades several theoretical and empirical models have been proposed for evaluating shear strength of beam-to-column joints. The present paper reports an overview of the models currently available in the scientific literature for evaluating shear capacity of exterior beam-to-column joints. The present study is the first step of a wide analysis aimed at assessing such models and improving them. Moreover, the uncertainties deriving by applying the mentioned models will be also quantified therein, by means of well-established procedures for probabilistic seismic analysis of structures. The final results of that study are reported within a companion paper.
Tài liệu tham khảo
ACI-ASCEE Committee 352: (2002) Recommendation for design of beam-column joints in monolithic reinforced concrete structures (ACI 352-02). American Concrete Institute, Farmington Hills
Attalla SA (1997) Seismic shear capacity of beam-column joints in multi-story reinforced concrete frame buildings. PhD dissertation, Civil Engineering Department, University of Southern California, p 300
Attaalla SA (2004) General analytical model for nominal shear stress of type 2 normal- and high-strength concrete beam-to-column joints. ACI Struct J 101(1): 65–75
Bakir PG, Boduroglu HM (2002) A new design equation for predicting the joint shear strength of monotonically loaded exterior beam-to-column joints. Eng Struct 24: 1105–1117
CEB-FIP (1990) Model code for concrete structures, CEB-FIP international recommendations
Ehsani MR, Moussa AE, Vallenilla CR (1987) Comparison of inelastic behavior of reinforced ordinary and high strength concrete frames. ACI Struct J 84
EN 1992-1 (2005) Eurocode 2: design of concrete structures. Part 1: General rules and rules for buildings
EN 1998-3 (2005) Eurocode 8: design of structures for earthquake resistance. Part 3: assessment and retrofitting of buildings
Favvata MJ, Izzuddin BA, Karayannis CG (2008) Modelling exterior beam-column joints for seismic analysis of RC frame structures. Earthq Eng Struct Dyn 37: 1527–1548
Hanson W, Connor HW (1967) Seismic resistance of reinforced concrete beam-column joints. J Struct Div
Hegger J, Sherif A, Roeser W (2003) Nonseismic design of beam-column joints. ACI Struct J 100(5): 654–664
Hwang SJ, Lee HJ (1999) Analytical model for predicting shear strength of exterior reinforced concrete beam-column joints for seismic resistance. ACI Struct J 96(5)
Hwang SJ, Lee HJ (2002) Strength prediction for discontinuity regions by softened strut-and-tie model. J Struct Eng 128(12)
Kim J, LaFave JM (2007) Key influence parameters for the joint shear behaviour of reinforced concrete (RC) beam-column connections. Eng Struct 29: 2523–2539
Kim J, LaFave JM (2009) Joint shear behaviour of reinforced concrete beam-column connections subjected to seismic lateral loading. Newmark Structural Engineering Laboratory—NSEL Report Series, NSEL-020
Kim J, LaFave JM, Song J (2007) A new statistical approach for joint shear strength determination of RC beam-column connections subjected to lateral earthquake loading. Struct Eng Mech 27(4): 439–456
Kim J, LaFave JM, Song J (2009) Joint shear behaviour of reinforced concrete beam-column connections. Mag Concr Res 61(2): 119–132
Lima C, Martinelli E, Faella C (2012) Shear strength of exterior beam-to-column reinforced concrete joints—Part. 2: assessment, recalibration and relevant factors. Companion Paper. doi:10.1007/s10518-012-9342-2
Ortiz (Reyes de) I (1993) Strut and tie modelling of reinforced concrete short beams and beam-column joints. PhD Thesis, University of Westminster
Pampanin S, Magenes G, Carr A (2003) Modelling of shear hinge mechanism in poorly detailed RC beam-column joints. Fib symposium on concrete structures in seismic regions, Paper 171, Athens, Greece
Pantazopoulo S, Bonacci J (1992) Considerations of questions about beam-column joints. ACI Struct J 89(1): 27–36
Parker DE, Bullman PJM (1995) Shear strength of reinforced concrete-the influence of shear span. Struct Eng 73(23–24): 413
Parker DE, Bullman PJM (1997) Shear strength within reinforced concrete beam-column joints. Struct Eng 75(4): 53–57
Parra-Montesinos GJ, Wight JK (2002) Prediction of strength and shear distortion in R/C beam-column joints. In behaviour and design of concrete structures for seismic performance. American Concrete Institute, sp. 197, pp 191–214, Detroit, Michigan
Paulay T, Priestley MJN (1992) Seismic design of reinforced concrete and masonry building. Wiley, New York
Pinto PE, Giannini R, Franchin P (2004) Seismic reliability analysis of structures. IUSS Press, Pavia
Russo G, Somma G (2006) Shear strength of exterior beam-column joints under seismic loading. Fib—federation Internationale du Beton, proceedings of the 2nd international congress, Naples, Italy
Sarsam KF, Phillips ME (1985) The shear design of in-situ reinforced beam-column joints subjected to monotonic loading. Mag Concr Res 37(130): 16–28
Scott RH, Feltham I, Whittle RT (1994) Reinforced beam-column connections and BS 8110. Struct Eng 72(4): 55–60
Tsonos AG (2007) Cyclic load behavior of reinforced concrete beam-column subassemblages of modern structures. ACI Struct J 104(4)
Vollum RL, Newman JB (1999) The design of external, reinforced concrete beam-column joints. Struct Eng 77(23–24): 21–27
Vollum R, Parker D (2008) External beam-column joints: design to Eurocode 2. Mag Concr Res 60(7): 511–521
Zhang L, Jirsa JO (1982) A study of shear behaviour of RC beam-column joints. PMFSEL Report No. 82-1, University of Texas at Austin