Boost converter design for ferrite core compatible with strong magnetic fields
Tóm tắt
Boost converters with a ferrite core are widely used in neurostimulators. However, there may be some problems if it is used in a strong magnetic field because the saturation of the ferrite core leads to a serious decline in the inductance value. To evaluate whether a converter can work normally in a strong magnetic field, it is critical to obtain the lower limit value of the inductance of the converter. Besides, small inductance is easy to fit the small volume of a converter and is also safe in some special scenarios. Therefore, this paper is mainly devoted to establishing the minimum inductance design criterion of boost converters with a pulse load. The operational modes and equivalent circuit considering the parasitic resistance of boost converter components are presented. Then the mathematical formula for the minimal inductance value is derived through theoretical analysis of the components’ current and output voltage. A digital simulation model of a boost converter is established to verify the theoretical analysis. Sets of comparison curves between the theoretical analysis and the simulation show that their results are in good agreement verifying the feasibility of the proposed method. The results in this paper provide theoretical support for the compatibility of converters containing a ferrite core inductor in a strong magnetic field and for the design requirement of a converter with a little volume inductor.
Tài liệu tham khảo
Hamm-Faber, T.-E., Gultuna, I., Van Gorp, E.-J., Aukes, H.: High-dose spinal cord stimulation for treatment of chronic low back pain and leg pain in patients with FBSS, 12-month results: a prospective pilot study. Neuromodulation 23(1), 118–125 (2020)
Geller, E.-B.: Responsive neurostimulation: review of clinical trials and insights into focal epilepsy. Epilepsy Behav. 88, 11–20 (2018)
Park, J.-K., Cremers, S., Kossler, A.-L.: Neurostimulation for tear production. Curr. Opin. Ophthalmol. 30(5), 386–394 (2019)
Bakhtiari, S., Altinkaya, A., Pack, C.-C., Sadikot, A.-F.: The role of the subthalamic nucleus in inhibitory control of oculomotor behavior in Parkinson’s disease. Sci. Rep. 10(1), 1–11 (2020)
Shen, L.-H., Jiang, C.-Q., Hubbard, C.-S., Ren, J.-X., et al.: Subthalamic nucleus deep brain stimulation modulates 2 distinct neurocircuits. Ann. Neurol. 88(6), 1178–1193 (2020)
Llyes, A., Toth, E., Pizarro, D., Riley, K.-O., Pati, S.: Modulation of neural oscillations by vagus nerve stimulation in posttraumatic multifocal epilepsy: case report. J. Neurosurg. 131(4), 1079–1085 (2019)
Welch, W.-P., Sitwat, B., Sogawa, Y.: Use of vagus nerve stimulator on children with primary generalized epilepsy. J. Child Neurol. 33(7), 449–452 (2018)
Yoo, H.-J., Hoof, C.-V.: Bio-medical CMOS ICs. Springer, New York (2011)
Li, Y., Lin, S.-L., Zhao, Y.-X., Wu, H., Wang, Y., Zhang, Z.: Design and analysis of output voltage ripple in buck converter with LC low-pass filter for the explosive environment. Fresenius Environ. Bull. 28(11A), 8789–8799 (2019)
Hu, W., Zhang, F.-Y., Xu, Y.-W., Chen, X.-B.: Output voltage ripple analysis and design considerations of intrinsic safety flyback converter based on energy transmission modes. J. Power Electron. 14(5), 908–917 (2014)
Liu, S., Liu, J., Mao, H., Zhang, Y.: Analysis of operating modes and output voltage ripple of boost DC-DC converters and its design considerations. IEEE Trans. Power Electron. 23(4), 1813–1821 (2008)
Babaei, E., Mahmoodieh, M., Sabahi, M.: Investigating buck DC-DC converter operation in different operational modes and obtaining the minimum output voltage ripple considering filter size. J. Power Electron. 11(6), 793–800 (2011)
Babaei, E., Mahmoodieh, M., Mahery, H.: Operational modes and output-voltage-ripple analysis and design considerations of buck-boost DC-DC converters. IEEE Trans. Ind. Electron. 59(1), 381–391 (2012)
Kim, D., Choe, G., Lee, B.: DCM analysis and inductance design method of interleaved boost converters. IEEE Trans. Power Electron. 28(10), 4700–4711 (2013)
Suga, I., Takeshima, Y., Kurokawa, F.: Inductance design method for boost converter with voltage clamp function. IEICE Trans. Commun. E96B(1), 81–87 (2013)
Kondrath, N., Ayachit, A., Kazimierczuk, M.: Minimum required magnetising inductance for multiple-output flyback DC-DC converter in CCM. Electron. Lett. 51(12), 930–931 (2015)