Bonding strength and thermal shock resistance of a novel bilayer (c‐AlPO4‐SiCw‐mullite)/SiC coated carbon fiber reinforced CMCs

Journal of the American Ceramic Society - Tập 103 Số 1 - Trang 82-93 - 2020
Pengju Chen1, Peng Xiao2,1, Zhuan Li2,1, Ling Pan1, Jinwei Li1, Zeyan Liu1, Dongmei Pu1, Yang Li1
1Powder Metallurgy Research Institute, Central South University, Changsha, China
2National Key Laboratory of Science and Technology for National Defense on High-strength Structural Materials, Central South University, Changsha, China

Tóm tắt

AbstractMullite coating, SiC whiskers toughened mullite coating (SiCw‐mullite), and cristobalite aluminum phosphate (c‐AlPO4) particle modified SiCw‐mullite coating (c‐AlPO4‐SiCw‐mullite) were prepared on SiC coated C/SiC composites using a novel sol‐gel method combined with air spraying. Results show that molten SiO2 formed by the oxidation of SiC whiskers and molten c‐AlPO4 improved the bonding strength between mullite outer coating and SiC–C/SiC composites due to their high‐temperature bonding properties. The bonding strength between mullite, SiCw‐mullite, c‐AlPO4‐SiCw‐mullite outer coatings and SiC–C/SiC composites were 2.41, 4.31, and 7.38 MPa, respectively. After 48 thermal cycles between 1773 K and room temperature, the weight loss of mullite/SiC coating coated C/SiC composites was up to 11.61%, while the weight losses of SiCw‐mullite/SiC and c‐AlPO4‐SiCw‐mullite/SiC coatings coated C/SiC composites were reduced to 7.40% and 5.12%, respectively. The addition of appropriate SiC whiskers can considerably improve the thermal shock resistance of mullite coating owing to their excellent mechanical properties at high temperature. In addition, c‐AlPO4 particles can further improve the thermal shock resistance of SiCw‐mullite coating due to their high‐temperature bonding and sealing properties. No obvious micro‐pores and cracks were observed on the surface of c‐AlPO4‐SiCw‐mullite coating after 48 thermal cycles due to timely healing effect by formation of secondary mullite.

Từ khóa


Tài liệu tham khảo

10.1111/j.1744-7402.2008.02330.x

10.1111/j.1551-2916.2010.04376.x

10.1016/S0008-6223(00)00148-2

10.1007/s10853-018-2700-y

10.1016/j.jeurceramsoc.2019.01.014

10.1016/j.jeurceramsoc.2013.12.012

10.1016/j.surfcoat.2013.01.011

10.1016/j.ceramint.2016.09.171

10.1016/j.corsci.2012.08.003

10.1016/j.ceramint.2018.06.082

10.1016/j.compositesb.2018.03.035

10.1016/j.surfcoat.2016.08.072

10.1016/j.surfcoat.2018.07.041

10.1016/j.jeurceramsoc.2014.09.038

10.1111/j.1151-2916.1997.tb03256.x

10.1016/j.jeurceramsoc.2013.12.049

10.1016/S1003-6326(17)60045-1

10.1016/j.corsci.2014.07.008

10.1016/j.jallcom.2017.03.108

10.1016/j.jeurceramsoc.2015.06.033

10.1016/j.corsci.2016.02.003

10.1007/s40145-017-0248-y

10.1016/j.jmst.2012.11.001

10.1016/S0955-2219(01)00535-0

10.1016/j.carbon.2005.09.026

10.1016/j.apsusc.2006.07.092

10.1016/j.ceramint.2012.07.024

10.1016/S0257-8972(97)00474-X

10.1016/j.surfcoat.2011.05.012

10.1007/s11666-013-0011-z

10.1016/j.jeurceramsoc.2016.07.009

10.1016/j.compositesa.2017.01.024

10.1016/j.ceramint.2018.08.266

10.1016/j.jallcom.2017.11.210

10.1016/j.ceramint.2018.06.165

10.1016/j.ceramint.2018.09.255

10.1016/j.surfcoat.2018.01.006

10.1016/j.jallcom.2017.03.205

10.1016/j.ceramint.2018.07.040

10.1016/j.jeurceramsoc.2018.08.022