Application of the Air-Jet Laser Detection Technology for Asphalt Binders
Springer Science and Business Media LLC - Trang 1-9 - 2023
Tóm tắt
A fast and convenient technique for Asphalt Binders was proposed in this paper, which was based on air-jet pressurized and laser to detect the transient deformation and creep recovery of asphalt. Taking five kinds of asphalt and modified asphalt commonly used in China as the research objects, the performance of asphalt were tested and analyzed by adopting the Penetration Test, Dynamic Shear Rheological (DSR) Test, Multiple Stress Creep and Recovery (MSCR) Test and the proposed test technology. The results verified the feasibility of the proposed test technology and the correlation between the traditional tests and the proposed test technology. The results demonstrated that the proposed test technology had good discrimination ability for different kinds of asphalt and could effectively reflect the performance differences. The new test protocol was similar to the Penetration Test. There was a significant correlation between the maximum deformation index and penetration index. The correlation coefficient was above 0.8, and the p value was much less than 0.01. It could be used as a possible alternative to the Penetration Test. The proposed new test was relatively convenient and fast compared with the dynamic shear test. There was a linear correlation between the maximum deflection index and the complex shear modulus G*, and the correlation coefficient between the recovery index and the phase angle is above 0.8, which indicated that the proposed new test and the DSR test had a significant correlation. There was also a good correlation between the creep recovery index of MSCR test and the recovery data of the proposed new test method. The research results provided a new solution for the performance test and evaluation of asphalt in China.
Tài liệu tham khảo
JTG E20. (2011). Standard test methods of bitumen and bituminous mixtures for highway engineering. Ministry of Communications.
JTG F40. (2004). Technical specification for construction of highway asphalt pavements. Ministry of Communications.
Hu, X. Q. (2015). Overview of road petroleum asphalt evaluation system. Architectural Engineering Technology and Design, 7, 878.
Zhang, Y. Z., & Wang, C. H. (2003). Classification of petroleum bitumen product standard. Petroleum Bitumen, 17(1), 44–47.
Huang, W. D., Sun, L. J., Zhang, Z. Q., et al. (2005). Study on penetration index of asphalt. Journal of Tongji University (Natural Science), 33(3), 306–310.
Li, F. J. (2013). Experimental study on asphalt penetration index. Road Construction and Machinery, 30(6), 57–63.
Gao, R. (2012). Study on key technical parameters and test methods of SBS modified asphalt. Changan: Chang’an University. in Chinese.
American Association of State Highway and Transportation Officials (AASHTO) T315-10. (2010). Standard method of test for determining the rheological properties of asphalt binder using a dynamic shear rheometer. In Standard specifications for transportation materials and methods of sampling and testing, Part 2B, 30th Edn.
Zhou, Q. H., & Jia, Y. (2008). Evaluation of high temperature performance test method of asphalt binder. Journal of Chang ’an University (Natural Science Edition), 28(2), 9–12.
The Multiple Stress Creep Recovery (MSCR) Procedure[R]. (2011). U.S. Department of Transportation, Federal Highway Administration, Office of Pavement Technology, FHWA-HIF-11-038.
Bahia, H. U., Hanson, D. I., Zeng, M. et al. (2001). Characterization of modified asphalt binders in superpave mix design[R]. NCHRP Report 459, Transportation Research Board, National Research Council.
Al-Adham, K., & Al-Abdul Wahhab, H. (2018). Influence of temperature on Jnr values of polymer modified asphalt binders. International Journal of Pavement Research and Technology, 11(6), 603–610.
Xu, S. F., Zhou, Z. H., Qian, P. Z., et al. (2003). Effectiveness analysis of modified asphalt in superpave specification. Journal of Highway and Transportation Science and Technology, 20(1), 41–44.
Liu, Z. Y., Zhang, M., & Shao, L. G. (2009). Effect of DSR on PG classification of modified asphalt. Journal of China and Foreign Highway, 29(6), 241–244.
Saboo, N., & Kumar, P. (2016). Use of flow properties for rheological modeling of bitumen. International Journal of Pavement Research and Technology, 9(1), 63–72.
Dongre, R., Youtcheff, J., Newman, J. (2015). Development of a Quality Assurance Test (QAT) for Asphalt Binders. In Proceedings of the Canadian technical asphalt association (CTAA), Winnipeg, Manitoba, Canada.
American Association of State Highway and Transportation Officials (AASHTO) T350. (2013). Multiple Stress Creep And Recovery Test. Standard specifications for transportation materials and methods of sampling and testing, Part 2B, 2013 Edition, Washington, D.C., T350-1:5.
Zhou, P. Y., Cheng, Z. H., Li, X., et al. (2015). Study on the effect of high viscosity modifier on asphalt performance. Journal of Highway and Transportation Research and Development (Applied Technology Edition), 11, 56–58.
Chen, J. S., & Lin, K. Y. (2005). Mechanism and behavior of bitumen strength reinforcement using fibers. Journal of Materials Science, 40(1), 87–95.