Application of experimental design and optimization to PFC model calibration in uniaxial compression simulation

1999

Potyondy, 2004, A bonded-particle model for rock, Int J Rock Mech Min Sci, 41, 1329, 10.1016/j.ijrmms.2004.09.011

NIST/SEMATECH e-Handbook of Statistical Methods, 〈www.itl.nist.gov/div898/handbook〉.

Plackett, 1946, The design of multifactorial experiments, Biometrika, 33, 305, 10.1093/biomet/33.4.305

Krishnan, 1998, Screening and selection of media components for lactic acid production using Plackett–Burman design, Bioproc Eng, 19, 61, 10.1007/PL00009003

Ahuja, 2004, Application of Plackett–Burman design and response surface methodology to achieve exponential growth for aggregated shipworm bacterium, Biotech Bioeng, 85, 666, 10.1002/bit.10880

Starzec, 2002, Application of two-level factorial design to sensitivity analysis of keyblock statistics from fracture geometry, Int J Rock Mech Min Sci, 39, 243, 10.1016/S1365-1609(02)00026-6

Eberhardt E. Brittle rock fracture and progressive damage in uniaxial compression. PhD thesis, Dept Geol Sci, University of Saskatchewan, 1998.

Eberhardt, 1999, Quantifying progressive pre-peak brittle fracture damage in rock during uniaxial compression, Int J Rock Mech Min Sci, 36, 361, 10.1016/S0148-9062(99)00019-4

Yoon KJ. Deformation and fracturing of rock by acoustic emission measurement and bonded-particle model analysis. MS thesis, School of Civil, Urban and Geosystem Engineering, Seoul National University, Seoul, 2002.

Potyondy DO, Cundall PA. Modeling of notch formation in the URL mine-by tunnel: Phase IV—Enhancements to the PFC model of rock, Itasca Consulting Group Inc. Report to Atomic Energy of Canada Limited (AECL) Issued as Ontario Hydro Nuclear Waste Management Division. Repot No. 06819-REP-01200-10002-R00, April 1999.

Bruno, 1991, Microstructural analysis of the inelastic behavior of sedimentary rock, Mech Mater, 12, 95, 10.1016/0167-6636(91)90057-7

Potyondy DO. Personal communication. 2006.

Venkataraman, 2002

Al-Shayea, 2000, Effect of confining pressure and temperature on mixed-mode (I–II) fracture toughness of a limestone rock, Int J Rock Mech Min Sci, 37, 629, 10.1016/S1365-1609(00)00003-4

Ingraffea AR. Mixed Mode fracture initiation in Indiana limestone and Westerly granite. In: Proceedings of the 22nd US Symposium on Rock Mech, Cambridge, MA, 1981. p. 186–91.

Rao, 2003, Shear fracture (Mode II) of brittle rock, Int J Rock Mech Min Sci, 40, 355, 10.1016/S1365-1609(03)00003-0

Backers T. Fracture toughness determination and micromechanics of rock under mode I and mode II loading. PhD thesis, University of Potsdam, 2005.

The MathWorks MATLAB Optimization toolbox User's Guide. 〈www.mathsworks.com〉.

Yoon YK. The effect of the loading condition and rock joint roughness on the hydraulic characteristics of rocks. PhD thesis, Seoul National University, Seoul, 1992.

Chang SH. Characterization of stress-induced damage in rock and its application on the analysis of rock damaged zone around a deep tunnel. PhD thesis, School of Civil, Urban and Geosystem Eng, Seoul National University. Korea. 2002.

Chang, 2001, Damage and fracture characteristics of Kimachi sandstone in uniaxial compression, Geosyst Eng, 4, 18, 10.1080/12269328.2001.10541163

JNC (Japan Nuclear Cycle) Development Institute. Mizunami Underground Research Laboratory Project. Results from 1996–1999 Period, 2003.

Zang, 2002, Acoustic emission controlled triaxial rock fracture and friction tests, 289

Zang, 1998, Source analysis of acoustic emissions in Aue granite cores under symmetric and asymmetric compressive loads, Geophys J Int, 135, 1113, 10.1046/j.1365-246X.1998.00706.x

Boutt, 2002, Simulation of sedimentary rock deformation: lab-scale model calibration and parameterization, Geophys Res Letts, 29, 1054, 10.1029/2001GL013987

Kennedy, 1999, Strategies for improving fermentation medium performance: a review, J Indust Microbio Biotech, 23, 456, 10.1038/sj.jim.2900755

Cruz, 1993, Medium optimization by a fractional factorial design for lipase production by Rhizopus delemar, J Ferm Bioeng, 76, 94, 10.1016/0922-338X(93)90063-E

Ahuja, 2004, Application of Plackett–Burman design and response surface methodology to achieve exponential growth for aggregated shipworm bacterium, Biotech Bioeng, 85, 666, 10.1002/bit.10880

Astakhov, 2004, An Application of the random balance method in conjunction with the Plackett–Burman screening design in metal cutting tests, J Test Eval, 32, 1, 10.1520/JTE11452

Driessche, 1996, A statistical Plackett–Burman design of the thermal process in the synthesis of the Bi-2223 HTSC, Supercon Sci Technol, 9, 843, 10.1088/0953-2048/9/10/002

Krishnan, 1998, Screening and selection of media components for lactic acid production using Plackett–Burman design, Bioproc Eng, 19, 61, 10.1007/PL00009003

Son, 1998, Production of a Ras farnesyl protein transferase inhibitor from Bacillus licheniformis using Plackett–Burman design, Biotech Letts, 20, 149, 10.1023/A:1005324407319

Zang A. Akustische Emissionen beim Sprödbruch von Gestein. Habilitationsschrift, University of Potsdam, Scientific Technical Report STR97/19, 1999.

Hong JS. Characteristics of creep deformation behavior of granite under uniaxial compression. MS thesis. School of Civil, Urban and Geosystem Engineering, Seoul National University, 2004.

Alber, 1999, Generation and visualization of microfractures in Cararra marble for estimating fracture toughness, fracture shear and fracture normal stiffness, Int J Rock Mech Min Sci, 36, 1065, 10.1016/S1365-1609(99)00069-6

Alber, 2001, Investigation of a limestone pillar failure. Part 1: stress history and application of fracture mechanics approach, Rock Mech Rock Eng, 34, 187, 10.1007/s006030170008