Analysis of maximum radial load capacity of hydrostatic journal bearing considering supply pressure limitation by a novel method

Lin Q.Y., Wei Z.Y., Wang N., Chen W. Analysis on the lubrication performances of journal bearing system using computational fluid dynamics and fluid-structure interaction considering thermal influence and cavitation. Tribology International. 2013;64:8–15. Sanandres, 1994, Dynamic force response of spherical hydrostatic journal bearings for cryogenic applications, Tribology Trans, 37, 463, 10.1080/10402009408983318 Martin, 2004, Measured stiffness and displacement coefficients of a stationary rotor hydrostatic bearing, Tribology Int, 37, 809, 10.1016/j.triboint.2004.04.010 Lee, 2013, A study on the influence of waviness error to a hydrostatic bearing for a crankshaft pin turner, Tribology Trans, 56, 1077, 10.1080/10402004.2013.823532 Cha, 2015, Nonlinear dynamic behaviour of vertical and horizontal rotors in compliant liner tilting pad journal bearings: Some design considerations, Tribology Int, 82, 142, 10.1016/j.triboint.2014.10.011 Teo, 2009, High-speed operation of a gas-bearing supported mems-air turbine, J Tribology-Trans Asme, 131, 10.1115/1.3123343 Leonard, 1973, Dynamic force coefficients and mechanism of instability in hydrostatic journal-bearings, Wear, 23, 277, 10.1016/0043-1648(73)90016-1 Jain, 1992, Analytical study of a flexible hybrid journal bearing system using different flow-control devices, Tribology Int, 25, 387, 10.1016/0301-679X(92)90076-Y Sanandres, 1995, Turbulent-flow hydrostatic bearings - analysis and experimental results, Int J Mech Sci, 37, 815, 10.1016/0020-7403(94)00104-R Metman, 1986, Load-capacity of multi-recess hydrostatic journal bearings at high eccentricities, Tribology Int, 19, 29, 10.1016/0301-679X(86)90092-7 Untaroiu, 2017, Effect of recess shape on the performance of a high-speed hybrid journal bearing, J Eng Gas Turbines Power-Trans Asme, 139 Raud, 2013, Numerical modelling of hydrostatic lift pockets in hydrodynamic journal bearings - Application to low speed working conditions of highly loaded tilting pad journal bearings, Mech Ind, 14, 327, 10.1051/meca/2013073 Kumar, 2020, Influence of lubricants on the performance of journal bearings - a review, Tribology-Mater Surf Interfaces, 14, 67, 10.1080/17515831.2020.1712112 Michalec, 2021, A review of the design and optimization of large-scale hydrostatic bearing systems, Eng Sci Technol- Int J-Jestech, 24, 936 Nicodemus, 2010, Influence of wear on the performance of multirecess hydrostatic journal bearing operating with micropolar lubricant, J Tribology-Trans Asme, 132 Yi, 2022, Static load characteristics of hydrostatic journal bearings: measurements and predictions, Sensors, 22 Liang, 2014, A new method for calculating the static performance of hydrostatic journal bearing, Tribology Int, 77, 72, 10.1016/j.triboint.2014.04.019 Singh, 2004, Performance of membrane compensated multirecess hydrostatic/hybrid flexible journal bearing system considering various recess shapes, Tribology Int, 37, 11, 10.1016/S0301-679X(03)00110-5 Sharma, 1998, Performance of hydrostatic/hybrid journal bearings with unconventional recess geometries, Tribology Trans, 41, 375, 10.1080/10402009808983761 Tomar, 2022, Non-Newtonian lubrication of hybrid multi-recess spherical journal bearings with different geometric shapes of recess, Tribology Int, 171 Verma, 2011, Analysis of capillary compensated hydrostatic journal bearing operating with micropolar lubricant, Ind Lubr Tribology, 63, 192, 10.1108/00368791111126617 Liu, 2017, A review of hydrostatic bearing system: Researches and applications, Adv Mech Eng, 9 Charki, 2014, Reliability of a hydrostatic bearing, J Tribology-Trans Asme, 136 Ren, 2016, Stability analysis of water-lubricated journal bearings for fuel cell vehicle air compressor, Tribology Int, 95, 342, 10.1016/j.triboint.2015.11.029 Wang, 2023, Simplified calculation of recess pressure considering the hydrodynamic effect, J Tribology, 145 Hsu, 1966, Non-Newtonian flow in infinite-length full journal bearing, Mech Eng, 88, 66-& Grabovskii, 1999, Optimum design of infinite journal bearing with a minimum of the friction moment, Pmm J Appl Math Mech, 63, 453, 10.1016/S0021-8928(99)00057-X Wierzcholski, 1977, Effect of force of inertia and of variable oil viscosity on pressure distribution in a journal bearing of infinite length, Wear, 45, 1, 10.1016/0043-1648(77)90098-9 Liang, 2013, A method for measuring the hydrodynamic effect on the bearing land, Tribology Int, 67, 146, 10.1016/j.triboint.2013.07.020 Xu, 2022, Reynolds boundary condition realization in journal bearings: Location of oil film rupture boundary with layering-sliding mesh method, Tribology Int, 165 He, 2014, Mixed-lubrication analysis of marine stern tube bearing considering bending deformation of stern shaft and cavitation, Tribology Int, 73, 108, 10.1016/j.triboint.2014.01.013 Ai, 1994, The influence of moving dent on point ehl contacts, Tribology Trans, 37, 323, 10.1080/10402009408983301 Ai, 1993, A transient model for microelastohydrodynamic lubrication with 3-dimensional irregularities, J Tribology-Trans Asme, 115, 102, 10.1115/1.2920961 Zhang, 2020, An improved lumped parameter method for calculating static characteristics of multi-recess hydrostatic journal bearings, Proc Inst Mech Eng Part J-J Eng Tribology, 234, 301, 10.1177/1350650119855242