Analysis of burst tests and long-term hydrostatic tests in produced water pipelines

da Costa Mattos, 2009, An alternative methodology to repair localized corrosion damage in metallic pipelines with epoxy resins, Mater Des, 30, 3581, 10.1016/j.matdes.2009.02.026

Veil JA, Puder M, Elcock D, Redweik Jr. RA. White paper describing produced water from production of crude oil, natural gas, and coal bed methane, prepared by Argonne National Laboratory, Argonne, Illinois for the US Department of Energy, National Energy Technology Laboratory; 2004. <http://www.evs.anl.gov/pub/dsp_detail.cfm?PubID=1715>.

ASME Boiler and Pressure Vessel Code – Section VII – Division 1, 1992 ed. 1995 addenda.

Murnaghan, 1951

Shyue, 2004, A fluid-mixture type algorithm for barotropic two-fluid flow problems, J Comput Phys, 200, 718, 10.1016/j.jcp.2004.05.003

Farhat, 2008, A higher-order generalized ghost fluid method for the poor for the three-dimensional two-phase flow computation of underwater explosions and implosions, J Comput Phys, 227, 7674, 10.1016/j.jcp.2008.04.032

Durban, 1979, Large strain solution for pressurized elasto-plastic tubes, Trans ASME J Appl Mech, 46, 228, 10.1115/1.3424511

Chistopher, 2002, A comparative study on failure pressure estimations of unflawed cylindrical vessels, Int J Pres Ves Pip, 79, 53, 10.1016/S0308-0161(01)00126-0

Durban, 1988, A finite strain axially symmetric solution for elastic tubes, Int J Solids Struct, 24, 675, 10.1016/0020-7683(88)90016-9

Durban, 1992, A general solution for the pressurized elasto-plastic tube, Trans ASME J Appl Mech, 59, 20, 10.1115/1.2899431

Law, 2007, Prediction of failure strain and burst pressure in high yield-to-tensile strength ratio linepipe, Int J Pres Ves Pip, 84, 487, 10.1016/j.ijpvp.2007.04.002

Xian-Kui, 2012, Evaluation of burst pressure prediction models for line pipes, Int J Pres Ves Pip, 89, 85, 10.1016/j.ijpvp.2011.09.007

Beena, 1995, Destructive stress of 15CDV6 steel rocket motor cases and their application to lightweight design, Int J Pres Ves Pip, 62-3, 313, 10.1016/0308-0161(94)00026-F

Subhananda Rao, 2005, Effect of long-seam mismatch on the burst pressure of maraging steel rocket motor cases, Eng Fail Anal, 12-2, 325

da Costa Mattos, 2010, Approximate local elasto-plastic solution for notched plates undergoing cyclic tensile loading, Mater Des, 31, 4336, 10.1016/j.matdes.2010.03.050

Loureiro SMNA. Reinforcement of cylindrical pressure vessels using polymeric composites (in Portuguese). MSc thesis, COPPE – Universidade Federal do Rio de Janeiro; 1999.

ASTM Standart B557. Standard test methods for tension testing wrought and cast aluminum- and magnesium-alloy products.

Margetson J. Burst pressure predictions of rocket motors. AIAA Paper No.78-1567. AIAA/SAE 14th Joint Propulsion Conference Las Vegas, NV USA; 1978.