Analysis of a Sound Signal for Quality Monitoring in Laser Microlap Welding

Applied Sciences - Tập 10 Số 6 - Trang 1934
Bo-Si Kuo1, Ming‐Chyuan Lu1
1Department of Mechanical Engineering, National Chung Hsing University, 145 Xingda Rd., South Dist., Taichung 402, Taiwan

Tóm tắt

This study focused on correlation analysis between welding quality and sound-signal features collected during microlaser welding. The study provides promising features for developing a monitoring system that detects low joint strength caused by a gap between metal sheets after welding. To obtain sound signals for signal analysis and develop the monitoring system, experiments for laser microlap welding were conducted on a laser microwelding platform by installing a microelectromechanical system (MEMS) microphone away from the welding point, and an acoustic emission (AE) sensor on the fixture. The gap between two metal sheet layers was controlled using clamp force, a pressing bar, and the appropriate installation of a thin piece of paper between the metal sheets. After sound signals from the microphone were collected, the correlation between features of time-domain sound signals and of welding quality was analyzed by categorizing the referred signals into eight sections during welding. After appropriately generating the features after signal analysis and selecting the most promising features for low-joint-strength monitoring on the basis of scatter index J, a hidden Markov model (HMM)-based classifier was applied to evaluate the performance of the selected sound-signal features. Results revealed that three sound-signal features were closely related to joint-strength variation caused by the gap between two metal-sheet layers: (1) the root-mean-square (RMS) value of the first section of sound signals, (2) the standard deviation of the first section of sound signals, and (3) the standard deviation to the RMS ratio of the second section of sound signals. In system evaluation, a 100% classification rate was obtained for normal and low-bonding-strength monitoring when the HMM-based classifier was developed on the basis of the three selected features.

Từ khóa


Tài liệu tham khảo

Shao, 2005, Review of Techniques for On-line Monitoring and Inspection of Laser Welding, J. Phys. Conf. Ser., 15, 101, 10.1088/1742-6596/15/1/017

Smith, E.T. (1999). Monitoring Laser Weld Quality Using Acoustic Signals. [Ph.D. Thesis, University of Michigan].

Sun, A.S. (2000). Multiple Sensor Monitoring of Laser Welding. [Ph.D. Thesis, University of Michigan].

Shimada, W., Ohmine, M., Hoshinouchi, S., and Kobayashi, M. (1982, January 24–26). Study on In-Process Assessment of Joint Efficiency in the Laser Welding Process. Proceedings of the International Symposium of the Japan Welding Society, Osaka, Japan.

Koch, 1992, Seam Geometry Monitoring for Tailored Welded Blanks, LIA, 74, 123

Gu, 1996, A Statistical Approach to Acoustic Monitoring of Laser Welding, J. Phys. Appl. Phys., 29, 556, 10.1088/0022-3727/29/3/011

Grad, 2004, Feasibility Study of Acoustic Signals for On-Line Monitoring in Short Circuit Gas Metal Arc Welding, Int. J. Mach. Tools Manuf., 44, 555, 10.1016/j.ijmachtools.2003.10.016

Houlot, 1997, Integration of Real Time Quality Control Systems in a Welding Process, J. Laser Appl., 9, 95, 10.2351/1.4745449

Luo, 2005, Application of Artificial Neural Network in Laser Welding Defect Diagnosis, J. Mater. Process. Technol., 170, 403, 10.1016/j.jmatprotec.2005.06.008

Matteson, A., Morris, R., and Tate, R. (1993, January 20–24). Real-Time GMAW Quality classification using an artificial neural network with airborne acoustic signals as inputs. Proceedings of the 12th International Conference on Offshore Mechanics and Arctic Engineering III-A, Glasgow, Scotland.

Lin, R.H., and Fischer, G.W. (1995, January 22–27). An On-Line Arc Welding Quality Monitor and Process Control System. Proceedings of the IEEE Conference on Industrial Automation and Control Emerging Technology Applications, Taipei, Taiwan.

Farson, 1996, Frequency–Time Characteristics of Air-Borne Signals from Laser Welds, J. Laser Appl., 8, 33, 10.2351/1.4745403

Jin, 2002, A Study on Fresnel Absorption and Reflections in the Keyhole in Deep Penetration Laser Welding, J. Phys. D Appl. Phys., 35, 2304, 10.1088/0022-3727/35/18/312

Huang, W., and Kovacevic, R. (2009, January 4–7). Noise Reduction During Acoustic Monitoring of Laser Welding of High-Strength Steels. Proceedings of the ASME 2009 International Manufacturing Science and Engineering Conference, West Lafayette, IN, USA. (MSEC2009-84080).

Chien, K. (2012). Applications of Acoustic Emission and Sound Signal for Welding Defect Monitoring in Nd:YAG Laser Thin Plate Butt Welding. [Master’s Thesis, National Chung Hsing University].

Hsieh, 2012, Application of backpropagation neural network for spindle vibration-based tool wear monitoring in micro-milling, Int. J. Adv. Manuf. Technol., 61, 53, 10.1007/s00170-011-3703-x

Wang, C.Y. (2018). The Development of Tool Condition Monitoring in the Millingof Inconel 718 by Recurrent HMMs. [Master’s Thesis, National Chung Hsing University].