Airfoil smoothing using unconditional optimization
Aerospace Systems - Trang 1-11 - 2023
Tóm tắt
The paper considers the smoothing of tabulated curves describing airfoils. Smoothing is required to eliminate airfoil contour distortions that occur during the design of the aircraft wing surface. The problem of ensuring a smooth change in the curvature of the smoothed contour is presented as a problem of minimizing the quadratic function of many variables. To minimize the objective quadratic function, the gradient descent method with a constant step was used. According to the developed technique, with the help of a computer program, the smoothing of the airfoil was carried out. As a result, a rather smooth diagram of the profile curvature was obtained, which confirmed the effectiveness of the developed smoothing technique.
Tài liệu tham khảo
Zhang Y, Fang X, Chen H, Fu S, Duan Z, Zhang Y (2015) Supercritical natural laminar flow airfoil optimization for regional aircraft wing design. Aerosp Sci Technol 43:152–164
Zhao T, Zhang Y, Chen H, Chen Y, Zhang M (2016) Supercritical wing design based on airfoil optimization and 2.75D transformation. Aerosp Sci Technol 56:168–182
Runze LI, Deng K, Zhang Y, Chen H (2018) Pressure distribution guided supercritical wing optimization. Chin J Aeronaut 31(9):1842–1854
Zhang S, Li H, Abbasi AA (2019) Design methodology using characteristic parameters control for low Reynolds number airfoils. Aerosp Sci Technol 86:143–152
Sun G, Sun Y, Wang S (2015) Artificial neural network based inverse design: airfoils and wings. Aerosp Sci Technol 42:415–428
Derksen RW, Rogalsky T (2010) Bezier-PARSEC: an optimized aerofoil parameterization for design. Adv Eng Softw 41(7–8):923–930
Pérez-Arribas F, Castañeda-Sabadell I (2016) Automatic modelling of airfoil data points. Aerosp Sci Technol 55:449–457
Shevyakov VI (2011) Airdynamic quality criteria of aircraft outer surface. Civil Aviation High Technol (Nauchny Vestnik MGTU GA) 163:133–137
Gerasimov YY, Grachev VS, Kaburov IS, Ozerov VN, Tabolov MU, Fomin VM, Shishov SG (1982) Investigation of the flow around an aircraft wing section in flight and in a wind tunnel. TsAGI Sci J XII(3):1–11
Shevyakov VI (2017) Development of theoretical foundations and practical methods for implementing the aerodynamic perfection of aircraft of the transport category, taking into account the fulfillment of certification requirements for flight safety. Dissertation for the degree of Doctor of Technical Sciences, Moscow State Technical University of Civil Aviation
Egorov EV (1987) Interpolation of a discrete curve by polynomials of even degrees. Descriptive geometry and computer graphics in the practice of solving engineering problems, Omsk, pp 81–83
Tuzov AD (1976) Smoothing of functions specified by tables. Methods of spline functions. Comput Syst 68:61–66
Esheeva IR (2006) Automation system for designing optimal contours of complex surfaces. Dissertation for the degree of Ph.D., East Siberia State University of Technology
Davydov YV, Zlygarev VA (1987) Wing geometry. Publishing house Mashinostroenie, Moscow
Tuzov AD, Davydov YV, Keel YG (2009) Computer-aided design of aircraft spatial layout based on orthogonal structures. Aviat Ind 4:8–11
Egorov EV, Erokhin AP (2014) Smoothing of the section of the aerodynamic contour with unregulated concavity. Flight 10:54–60
Deniskin YI, Yerokhin AP (2015) Smoothing of the aerodynamic contour area having unregulated concavity with a restriction of deviation from the reference coordinates of contour. Internet magazine “Naukovedenie” 7: 2
Deniskin YI, Yerokhin A, Artiukh V, Vershinin V, Pocebneva I (2019) Simulation of an aerodynamic profile with sections of ad hoc concavity. E3S Web Conf 110:01074
Berezin IS, Zhidkov NP (1962) Calculation methods, vol 1. Publishing house of physical and mathematical literature, Moscow
Panteleev AV, Letova TA (2005) Optimization methods in examples and tasks: Proc. allowance. Higher school, Moscow