A multi-bead overlapping model for robotic wire and arc additive manufacturing (WAAM)
Tóm tắt
Từ khóa
Tài liệu tham khảo
Agarwala, 1995, Direct selective laser sintering of metals, Rapid Prototyp J, 1, 26, 10.1108/13552549510078113
Lewis, 2000, Practical considerations and capabilities for laser assisted direct metal deposition, Mater Des, 21, 417, 10.1016/S0261-3069(99)00078-3
Taminger KM, Hafley RA. Electron beam freeform fabrication: a rapid metal deposition process. In: Proceedings of the 3rd annual automotive composites conference; 2003. p. 9–10.
Merz, 1994
Almeida PS, Williams S. Innovative process model of Ti–6Al–4V additive layer manufacturing using cold metal transfer (CMT). In: Proceedings of the twenty-first annual international solid freeform fabrication symposium. Austin, TX, USA: University of Texas; 2010.
Ding, 2011, Thermo-mechanical analysis of wire and arc additive layer manufacturing process on large multi-layer parts, Comput Mater Sci, 50, 3315, 10.1016/j.commatsci.2011.06.023
Wang, 2011, Morphology investigation on direct current pulsed gas tungsten arc welded additive layer manufactured Ti6Al4V alloy, Int J Adv Manuf Technol, 57, 597, 10.1007/s00170-011-3299-1
Mok, 2008, Deposition of Ti–6Al–4V using a high power diode laser and wire, Part I: investigation on the process characteristics, Surf Coat Technol, 202, 3933, 10.1016/j.surfcoat.2008.02.008
Brandl, 2011, Deposition of Ti–6Al–4V using laser and wire, part I: microstructural properties of single beads, Surf Coat Technol, 206, 1120, 10.1016/j.surfcoat.2011.07.095
Zhang, 2008, Characterization of laser powder deposited Ti–TiC composites and functional gradient materials, J Mater Process Technol, 206, 438, 10.1016/j.jmatprotec.2007.12.055
Karunakaran, 2010, Low cost integration of additive and subtractive processes for hybrid layered manufacturing, Robot Comput-Integr Manuf, 26, 490, 10.1016/j.rcim.2010.03.008
Mazumder, 2000, Closed loop direct metal deposition: art to part, Opt Lasers Eng, 34, 397, 10.1016/S0143-8166(00)00072-5
Wanjara, 2007, Electron beam freeforming of stainless steel using solid wire feed, Mater Des, 28, 2278, 10.1016/j.matdes.2006.08.008
Sreenathbabu, 2005, Statistical process design for hybrid adaptive layer manufacturing, Rapid Prototyp J, 11, 235, 10.1108/13552540510612929
Unocic, 2004, Process efficiency measurements in the laser engineered net shaping process, Metall Mater Trans B, 35, 143, 10.1007/s11663-004-0104-7
Rannar, 2007, Efficient cooling with tool inserts manufactured by electron beam melting, Rapid Prototyp J, 13, 128, 10.1108/13552540710750870
DuPont, 1995, Thermal efficiency of arc welding processes, Weld J (Including Welding Research Supplement), 74, 406s
Xiong, 2012, Vision-sensing and bead width control of a single-bead multi-layer part: material and energy savings in GMAW-based rapid manufacturing, J Clean Prod, 41, 82, 10.1016/j.jclepro.2012.10.009
Colegrove, 2013, Microstructure and residual stress improvement in wire and arc additively manufactured parts through high-pressure rolling, J Mater Process Technol, 213, 1782, 10.1016/j.jmatprotec.2013.04.012
Xiong, 2012, Bead geometry prediction for robotic GMAW-based rapid manufacturing through a neural network and a second-order regression analysis, J Intell Manuf, 25, 1
Suryakumar, 2011, Weld bead modeling and process optimization in hybrid layered manufacturing, Comput-Aided Des, 43, 331, 10.1016/j.cad.2011.01.006
Cao, 2011, Overlapping model of beads and curve fitting of bead section for rapid manufacturing by robotic MAG welding process, Robot Comput-Integr Manuf, 27, 641, 10.1016/j.rcim.2010.11.002
Xiong, 2012, Modeling of bead section profile and overlapping beads with experimental validation for robotic GMAW-based rapid manufacturing, Robot Comput-Integr Manuf, 29, 417, 10.1016/j.rcim.2012.09.011