Nội dung được dịch bởi AI, chỉ mang tính chất tham khảo
Một Phương Pháp Tăng Cường Độ Ổn Định Của Các Tính Chất Cơ Học Của Vòng Kim Loại Làm Từ Hợp Kim Titan VT6 Dùng Trong Động Cơ Tên Lửa Và Động Cơ Tuabin Khí Bằng Cách Hình Thành Cấu Trúc Vòng
Tóm tắt
Tóm tắt—Hành vi của hợp kim titan VT6 trong điều kiện rèn nóng được khảo sát. Các phương trình cấu thành, điều kiện ma sát và mô hình tiến hóa vi cấu trúc được tìm thấy. Các chuyển pha được mô tả bởi mô hình Johnson–Mehl–Avrami–Kolmogorov (JMAK). Công trình tập trung vào việc cung cấp độ ổn định của các tính chất cơ học của các vòng làm từ hợp kim titan VT6 bằng cách thu được cấu trúc hình cầu thông qua việc lựa chọn các chế độ phù hợp trong quá trình công nghệ.
Từ khóa
#hợp kim titan #VT6 #rèn nóng #tính chất cơ học #cấu trúc vi mô #mô hình JMAK #động cơ tên lửa #động cơ tuabin khíTài liệu tham khảo
Burlakov, I.A., Modeling the structure formation during hot deforming the billets of the parts of gas-turbine engines made of heat-resistant nickel alloy, J. Mach. Manuf. Reliab., 2016, no. 5, p. 95.
Mukhtarov, S.K., Utyashev, F.Z., and Sukhorukov, R.Y., Influence of the deformational heat treatment on the structure and mechanical properties of nickel-iron alloy, J. Mach. Manuf. Reliab., 2015, vol. 44, no. 1, p. 33.
Sukhorukov, R.U., Sidorov, A.A., Ibragimov, A.R., and Utyashev, F.Z., Mathematical modeling of the manufacturing process of axisymmetric aircraft parts by the local deformation method, Pis’ma Mater., 2015, no. 5 (2), p. 175.
Utyashev, F.Z. et al., Specific features of rolling of shaft of gas turbine engine under conditions of superplasticity, J. Mach. Manuf. Reliab., 2016, vol. 45, no. 1, p. 65.
Sukhorukov, R.Yu., et al., Physical and numerical modeling of the process of rolling off of a tapered shaft of aviation purpose, J. Mach. Manuf. Reliab., 2016, vol. 45, no. 6, p. 538.
Instructions on metallographic analysis of titanium alloys, Instructions, VIAM, 1974, no. 1054-76.
Cho, H. and Altan, T., Determination of flow stress and interface friction at elevated temperatures by inverse analysis technique, J. Mater. Proces. Technol., 2005, vol. 170, nos. 1–2, p. 64.
ASTM E0209-10, Practice for compression tests of metallic materials at elevated temperatures with conventional or rapid heating rates and strain rates.
Male, A.T., A method for the determination of the coefficient of friction of metals under conditions of bulk plastic deformation, J. Inst. Metal., 1964, vol. 93, p. 38.
GOST (State Standard) No. 5639-82. Steel and alloys. Methods for detecting and determining grain size.
ASTM E0562-11. Test method for determining volume fraction by systematic manual point count.
Stefansson, N., Semiatin, S.L., and Eylon, D., The kinetics of static globularization of Ti–6Al–4V, Metall. Mater. Trans. A, 2002, vol. 33, no. 11, p. 3527.
Alimov, A.I., Improving the technology of manufacturing rings of titanium alloy BT6 by determining rational modes of deformation, Cand. Sci. (Tech. Sci.) Dissertation, Moscow: Bauman Mosc. State Technol. Univ., 2017, p. 160.
Semiatin, S.L., Seetharaman, V., and Weiss, I., Flow behavior and globularization kinetics during hot working of Ti–6Al–4V with a colony alpha microstructure, Mater. Sci. Eng. A, 1999, vol. 263, no. 2, p. 257.