A Study of Combustion Characteristics of Gasified Coal Fuel

Journal of Engineering for Gas Turbines and Power - Tập 123 Số 1 - Trang 22-32 - 2001
Takuya Hasegawa1, Mikio Sato1, Toshihiko Nakata2
1Central Research Institute of Electric Power Industry, Yokosuka, Kanagawa, Japan
2Department of Aeronautics and Space Engineering, Tohoku University, Sendai, Miyagi, Japan

Tóm tắt

The development of integrated, coal-gasification combined cycle (IGCC) systems provides cost-effective and environmentally sound options for meeting future coal-utilizing power generation needs in the world. The Japanese government and the Electric Power Industries in Japan promoted research and development of an IGCC system. We have being working on developing a low-NOx combustion technology used in gas turbine combustors for IGCC. Each gaseous fuel produced from some raw materials contained CO and H2 as the main combustible components, and a small amount of CH4. Compositions and calorific values of gasified coal fuels varied widely depending on raw materials and gasifier types. Gaseous fuel, produced in various gasifiers, has a calorific value of 4–13 MJ/m3, which is about one-tenth to one-third that of natural gas. The flame temperatures of fuels increase as the fuel calorific value rises. When the fuel calorific value rises 8 MJ/m3 or higher, the flame temperature is higher than that of natural gas, and so NOx production from nitrogen fixation is expected to increase significantly. Also, some gasified coal fuels contain fuel nitrogen, such as ammonia, if the hot/dry type gas cleaning system is employed. These factors affect the combustion characteristics of the gasified coal fuel. In this paper, we clarified the influence of gasified coal fuel properties on NOx and CO emissions through experiments using a small diffusion burner and through numerical analysis based on reaction kinetics. The main results were as follows: 1 NH3 conversion to NOx increases with increasing CH4 concentration in gaseous fuel. 2 If gaseous fuel contains CH4, there will be some specific equivalence ratio in the primary combustion zone for the minimum NH3 conversion to NOx in the two-staged combustion. 3 Its specific equivalence ratio in the primary combustion zone increases with decreasing CH4 concentration in gaseous fuel. 4 If the fuel contains a small percent of CH4, there is no influence of the CO/H2 molar ratio in the fuel on the conversion rate of NH3 to NOx, while there is an influence in the case where fuel contains no CH4. The conversion rate increases with rises in the CO/H2 molar ratio. 5 As the pressure increases, the conversion rate of NH3 to NOx slightly decreases and the CO emission declines significantly.

Từ khóa


Tài liệu tham khảo

Mizutani, H. , 1995, “Future View of Combined Cycle,” The Thermal and Nuclear Power, Thermal and Nuclear Power Eng. Soc., 46, No. 469, pp. 1198–1222.

See, for example, Regenbogen, R. W., 1995, Proc. the 12th Annual Int. Pittsburgh Coal Conf., p. 78.

Ishizuka, S., and Tsuji, H., 1981, “An Experimental Study of Effect of Inert Gases on Extinction of Laminar Diffusion Flames,” Proc. 18th Symp. (Int.) on Combust. The Combust. Inst., Pittsburgh, PA, p. 695.

Morgan, G. H., and Kane, W. R., 1962, Proc. 9th Symp. (Int.) on Combust., The Combust. Inst., Pittsburgh, PA, p. 313.

Coward, H. F., and Jones, G. E., 1971, “Flammability Characteristics of Combustion Gases and Vapors,” Bulletin 627, Bureau of Mines.

Ishibasi, Y., and Kuroda, R., 1978, Proc. the 6th Annual Conf. Gas Turbine Soc. Jpn., p. 7.

Folsom, B. A., Courtney, C. W., and Heap, M. P., 1980, “The Effects of LBG Composition and Combustor Characteristics on Fuel NOx Formation,” ASME J. Eng. Power, 102, p. 459459.

Drake, M. C., Pitz, R. W., Correa, S. M., and Lapp, M., 1984, “Nitric Oxide Formation from Thermal and Fuel-Bound Nitrogen Sources in a Turbulent Nonpremixed Syngas Flame,” Proc. 20th Symp. (Int.) Combust., The Combust. Inst., Pittsburgh, PA, pp. 1983–1990.

Do¨bbeling, K., Eroglu, A., Winkler, D., Sattelmayer, T., and Keppel, W., 1996, “Low NOx Premixed Combustion of MBtu Fuels in a Research Burner,” ASME Paper 96-GT-126.

Pillsbury, P. W., Cleary, E. N. G., Singh, P. P., and Chamberlin, R. M., 1976, “Emission Results form Coal Gas Burning in Gas Turbine Combustors,” ASME J. Eng. Power, 98, p. 8888.

Clark, W. D., Folsom, B. A., Seeker, W. R., and Courtney, C. W., 1982, “Bench Scale Testing of Low-NOx LBG Combustors,” ASME J. Eng. Power, 104, p. 120120.

Battista, R. A., and Farrell, R. A., 1979, “Development of an Industrial Gas Turbine Combustor Burning a Variety of Coal-Derived Low Btu Fuels and Distillate,” ASME Paper 79-GT-172.

Beebe, K. W., et al., 1982. DOE/NASA/13111-11, NASA TM, 82985.

Do¨bbeling, K., Kno¨pfel, H. P., Polifke, W., Winkler, D., Steinbach, C., and Sattelmayer, T., 1994, “Low NOx Premixed Combustion of MBtu Fuels Using the ABB Double Cone Burner (EV Burner),” ASME Paper 94-GT-394.

Cook, C. S., Corman, J. C., and Todd, D. M., 1994, “System Evaluation and LBtu Fuel Combustion Studies for IGCC Power Generation,” ASME Paper 94-GT-366.

Sato, M., Nakata, T., and Yamauchi, K., 1990, “NOx Emission Characteristics of Coal-Derived Low Btu Gas Fuel,” J. Fuel Soc. Jpn., 69, No. 10, pp. 952–959.

Nakata, T., and Sato, M., 1991, “Reaction Analysis of Coal Gaseous Fuel in a Gas Turbine Combustor,” J. Jpn. Inst. Energy, 71, No. 1, pp. 84–41.

Yamauchi, K., Sato, M., and Nakata, T., 1991, “The Effect of CH4 Contained in Coal Gas Fuel on NOx Formation,” Trans. Jpn. Soc. Mech. Eng., Ser. B, 57, No. 535, pp. 811–818.

Nakata, T., Sato, M., and Hasegawa, T., 1998, “Reaction of Fuel NOx Formation for Gas Turbine Conditions,” Trans. ASME: J. Eng. Gas Turbines Power, 120, No. 3, pp. 474–480.

Sato, M., Nakata, T., Yoshine, T., and Yamada, M., 1990, “Development of a 1300 °C-Class Gas Turbine Combustor Burning Coal-Derived Low-Btu Gaseous Fuels,” Trans. Jpn. Soc. Mech. Eng., Ser. B, 56, No. 530, pp. 3147–3154.

Sato, M., Ninomiya, T., Abe, T., Yoshine, T., and Hasegawa, H., 1990, “Development of a 1300 °C-Class Gas Turbine Combustor Burning Coal-Derived Low-Btu Gaseous Fuels,” Trans. Jpn. Soc. Mech. Eng., Ser. B, 56, No. 532, pp. 3903–3909.

Sato, M., Nakata, T., Yoshine, T., and Yamada, M., 1991, “Development of a 1300 °C-Class Gas Turbine Combustor Burning Coal-Derived Low-Btu Gaseous Fuels,” Trans. Jpn. Soc. Mech. Eng., Ser. B, 57, No. 535, pp. 803–810.

Nakata, T., Sato, M., Ninomiya, T., Yoshine, T., and Yamada, M., 1992, “Development of a 1300 °C-Class Gas Turbine Combustor Burning Coal-Derived Low-Btu Gaseous Fuels,” Trans. Jpn. Soc. Mech. Eng., Ser. B, 58, No. 553, pp. 2890–2897.

Nakata, T., Sato, M., and Hasegawa, T., 1994, “A Study on Low NOx Combustion in LBG-Fueled 1500 °C-Class Gas Turbine,” ASME Paper 94-GT-218.

Hasegawa, T., Sato, M., and Ninomiya, T., 1997, “Effect of Pressure on Emission Characteristics in LBG-Fueled 1500 °C-Class Gas Turbine,” ASME Paper 97-GT-277.

Hasegawa, T., Hisarnatsu, T., Katsuki, Y., Sato, M., Yamada, M., Onoda, A., and Utsunomiya, M., 1998, “A Study of Low NOx Combustion Characteristics in Medium-Btu Fueled 1300 °C-Class Gas Turbine Combustor,” ASME Paper 98-GT-331.

Modern Power Systems Review, 1993, “Clean Coal 5 Eyes BGL Gasification at Camden,” August 1993, pp. 21–24.

Kalsall, G. J., Smith, M. A., and Cannon, M. F., 1994, “Low Emissions Combustor Development for an Industrial Gas Turbine to Utilize LCV Fuel Gas,” Trans. ASME J. Eng. Gas Turbines Power, 116, p. 559559.

Ichikawa, K., and Araki, S., 1996, “Test Results of the IGCC System by the 200T/D Nakoso Pilot Plant,” Proc. The 9th Thermal Engineering Symp., pp. 11–12.

Bush, W. V., Baker, D. C., and Tijm, P. J. A., 1991, “Shell Coal Gasification Plant(SCGP-1) Environmental Performance Results,” EPRI Interim Report No. GS-7397, Project 2695-1.

Ueda, T., Kida, E., Nakaya, Z., Shikata, T., Koyama, S., and Takagi, M., 1995, “Design of the HYCOL Gasifier,” Proc. Int. Conference Power Engineering-’95, pp. 242–247.

Modern Power Systems, 1994, “Biomass Looks Good for Gasification Process,” April 1994, pp. 61–65.

Consonni, S., Larson, E. D., and Berglin, N., 1997, “Black Liquor-Gasifier/Gas Turbine Cogeneration,” ASME Paper 97-GT-273.

Ashizawa, M., Takahashi, T., Taki, M., Mori, K., Kanehira, S., and Takeno, K., 1996, “A Study, on Orimulsion Gasification Technology,” Power-Gen ’96 Int., 8, pp. 235–243.

Hasegawa, T., and Sato, M., 1997, “Study on NOx Formation Characteristics of Medium Btu Coal Gasified Fuel,” Trans. Jpn. Soc. Mech. Eng., Ser. B, 63, No. 613, pp. 3123–3130.

Miller, J. A., and Bowman, C. T., 1989, “Mechanism and Modeling of Nitrogen Chemistry in Combustion,” Prog. Energy Combust. Sci., 15, pp. 287–338.

Hasegawa, T., and Sato, M., 1998, “Study of Ammonia Removal from Coal-Gasified Fuel,” Combust. Flame, 114, pp. 246–258.

Chase, Jr., M. W., Davies, C. A., Downey, Jr., J. R., Frurip, D. J., McDonald, R. A., and Syverud, A. N., 1985, “JANAF Thermodynamical tables 3rd Edition.,” J. Phys. Chem. Ref. Data, 14.

Kee, R. J., Rupley, F. M., and Miller, J. A., 1990, Sandia Report, SAND 87-8215B.

Hindmarsh, A. C., 1974, Lawrence Livermore Laboratory, Univ. California, Report No. UCID-30001, Rev. 3.

Pratt, D. T., Bowman, B. R., and Crowe, C. T., 1971, AIAA paper 71-713.

Martin, F. J., and Dederick, P. K., 1977, “NOx From Fuel Nitrogen in Two-Stage Combustion,” Proc. 16th Symp. (Int.) on Comb., The Comb. Institute., Pittsburg, PA, pp. 191–198.

Yamagishi, K., Nozawa, M., Yoshie, T., Tokumoto, T., and Kanegawa, Y., 1974, “A Study of NOx Emission Characteristics in Two-Stage Combustion,” Proc. 15th Symp. (Int.) on Comb., The Comb. Institute., Pittsburgh, PA, pp. 1157–1165

JSME Data Book: Formation Mechanisms and Controls of Pollutants in Combustion System, 1980, 47, JSME, Japan.

Sarofim, A. F., Williams, G. C., Modell, M., and Slater, S. M., 1975, “Conversion of Fuel Nitrogen to Nitric Oxide in Premixed and Diffusion Flames,” AIchE Symp. Ser., 71, No. 148, pp. 51–61.

Kato, K., Fujii, K., Kurata, T., and Mori, K., 1976, Trans. Jpn. Soc. Mech. Eng., 42, No. 354, pp. 582–589.

Fenimore, C. P. , 1972, “Formation of Nitric Oxide From Fuel Nitrogen in Ethylene Flames,” Combust. Flame, 19, No. 2, pp. 289–296.

Takagi, T., Ogasawara, M., Daizo, M., and Tatsumi, T., 1977, Trans. Jpn. Soc. Mech. Eng., 43, No. 368, p. 1426–1439.

Fenimore, C. P., 1976, “Effects of Diluents and Mixing on Nitric Oxide from Fuel-Nitrogen Species in Diffusion Flames,” Proc. 16th Symp. (Int.) on Comb., The Comb. Institute., Pittsburgh, PA, pp. 1065–1071.

Heap, M. P., Tyson, T. J., Cichanowicz, E., Gershman, R., Kau, C. J., Martin, G. B., and Lanier, W. S., 1976, “Environmental Aspects of Low BTU Gas Combustion,” Proc. 16th Symp. (Int.) on Comb., The Comb. Institute., Pittsburgh, PA, pp. 535–545.

Takagi, T., Tatsumi, T., Ogasawara, M., and Tatsumi, K., 1978, Trans. Jpn. Soc. Mech. Eng., 44, No. 388, pp. 4282–4291.

Kato, K., Fujii, K., Kurata, T., and Mori, K., 1977, Trans. Jpn. Soc. Mech. Eng., 43, No. 365, pp. 280–292.

Takagi, T., Ogasawara, M., Daizo, M., and Tatsumi, T., 1976, “NOx Formation From Nitrogen in Fuel and Air During Turbulent Diffusion Combustion,” Proc. 16th Symp. (Int.) Combust., The Comb. Institute, Pittsburgh, PA, pp. 181–188.

Thông tin
Thông tin xuất bản

Journal of Engineering for Gas Turbines and Power

Tập 123 Số 1

22-32

Thông tin tác giả