A Simplified Approach to Estimate Limiting Drawing Ratio and Maximum Drawing Load in Cup Drawing

Journal of Engineering Materials and Technology - Tập 126 Số 1 - Trang 116-122 - 2004
Daw-Kwei Leu1, Jen-Yu Wu1
1Department of Mechanical Engineering, Kuang-Wu Institute of Technology, 151, I-Der Street, Peitou, Taipei, Taiwan 112, Republic of China

Tóm tắt

A new and practically applicable equation, including the normal anisotropy R, the strain hardening exponent n, the friction coefficient μ, and the bending factor t0/rd for estimating the limiting drawing ratio LDR (a measure of drawability of sheet metal) in cup drawing of a cylindrical cup with a flat-nosed punch is derived by an elementary theory of plasticity in an explicit form. Whiteley’s and Leu’s equations for estimating the LDR, and Hill’s upper limit value of LDR, all are the special cases of the derived equation. The estimation of LDR agrees well with the experiment. It is shown that the most important parameters for LDR are the normal anisotropy R and friction coefficient μ, however the strain hardening exponent n has little effect on the LDR. On the other hand, a new and simple equation, incorporating the derived LDR and the critical drawing load Pc, for estimating the maximum drawing load Pd at a certain drawing ratio is derived. It also agrees well with the experiment. It is thereby possible to better understand and control the drawing limit of sheet metal in industry necessity.

Từ khóa


Tài liệu tham khảo

Whiteley, R. L., 1960, “The Importance of Directionality in Drawing Quality Sheet Steel,” Trans., ASM, 52, pp. 154–163.

Wright, J. C., 1962, “Relationship Between Mechanical Properties, Deep-Drawability and Stretch-Formability for Some Non-Ferrous Sheet Materials,” Sheet Metal Industries, 39, pp. 887–901.

Lilet, L., and Wybo, M., 1964, “An Investigation Into the Effect of Plastic Anisotropy and Rate of Work-Hardening in Deep Drawing,” Sheet Metal Industries, 41, pp. 783–815.

Shawki, G. S. A., 1965, “Assessing Deep-Drawing Qualities of Sheet Metal, Part III Combined Simulative Tests,” Sheet Metal Industries, 42, pp. 524–532.

Wilson, D. V., Sunter, B. J., and Martin, D. F., 1966, “A Single-Blank Test for Drawability,” Sheet Metal Industries, 43, pp. 465–476.

Atkinson, M., 1967, “Assessing Normal Anisotropic Plasticity of Sheet Metals,” Sheet Metal Industries, 44, pp. 167–178.

Thorp, J. M., 1973, “Sheet Drawability Assessed from a Two-Blank Cup-Drawing Test and Tensile Test,” Sheet Metal Industries, 50, pp. 99–104.

Keeler, S. P., and Backofen, W. A., 1960, Discussion to Ref. 1, Trans., ASM, 52, pp. 166.

Moore, G. G., and Wallace, J. F., 1964–65, “The Effect of Anisotropy on Instability in Sheet Metal Forming,” J. Inst. Met., 93, pp. 33–38.

Chiang, D. C., and Kobayashi, S., 1966, “The Effect of Anisotropy and Work-Hardening Characteristics on the Stress and Strain Distribution in Deep Drawing,” ASME J. Ind., 88, pp. 443–448.

Budiansky, B., and Wang, N. M., 1966, “On the Swift Cup Test,” J. Mech. Phys. Solids, 14, pp. 357–374.

El-Sebaie, M. G., and Mellor, P. B., 1972, “Plastic Instability Conditions in the Deep-Drawing of a Circular Blank of Sheet Metal,” Int. J. Mech. Sci., 14, pp. 535–556.

Hill, R., 1950, The Mathematical Theory of Plasticity, Clarendon Press, Oxford, UK.

Yamada, Y. , 1964, “Effects of R-Value on the Deep-Drawing of Sheet Metals,” J. Jpn. Soc. Technol. Plast., 5, pp. 183–194.

Mir, W. A., and Hillier, M. J., 1969, “Cup Drawing from an Anisotropic Blank,” ASME J. Eng. Ind., 89, pp. 766–771.

Kawai, N., Tomata, E., Moriya, K., Araki, H., Kondo, K., and Fujimura, Y., 1968, “The Effects of Processing Variables on Formability of Aluminum Sheets (1st Report, the Effect of Cold Reduction),” Bull. JSME, 12(53), pp. 1223–1231.

Eshel, G., Barash, M., and Johnson, W., 1986, “Rule Based Modeling for Planning Axisymmetrical Deep-Drawing,” J. Mater. Process. Technol., 14, pp. 1–115.

Shawki, G. S. A., 1965, “Assessing Deep-Drawing Qualities of Sheet Metal: Part II—Deep-Drawing Tests,” Sheet Metal Industries, 42, pp. 417–424.

Reissner, J., and Ehrismann, R., 1987, “Computer-Aided Deep-Drawing of Two-Part Cans,” CIRP Ann., 36, pp. 199–202.

Shinagawa, K., Mori, K., and Osakada, K., 1991, “Finite Element Simulation of Deep Drawing of Stainless Steel Sheet with Deformation-Induced Transformation,” J. Mater. Process. Technol., 27, pp. 301–310.

Chan, J. W., 1995, “A Study of Limitation of Sheet Metal Stretching and Drawing Processes,” Ph.D. Thesis, National Taiwan Institute of Technology, Taipei, Taiwan.

Venkatesh, V. C., and Goh, T. N., 1986, “A Note on Mathematical Models of Cup Drawing by the Guerin and Marform Processes,” J. Mech. Work. Technol., 13, pp. 273–278.

Saotome, Y., Yasuda, K., and Kaga, H., 2001, “Microdeep Drawability of Very Thin Sheet Steels,” J. Mater. Process. Technol., 113, pp. 641–647.

Moon, Y. H., Kang, Y. K., Park, J. W., and Gong, S. R., 2001, “Tool Temperature Control to Increase the Deep Drawability of Aluminum 1050 Sheet,” Int. J. Mach. Tools Manuf., 41, pp. 1283–1294.

Hosford, W. F., and Kim, C., 1976, “The Dependence of Deep-Drawability on Normal Anisotropy, Crystallographic Analysis,” Metall. Trans. A, 7A, pp. 468–472.

Hosford, W. F., 1977, “The Effect of Anisotropy and Work Hardening on Cup Drawing, Redrawing and Ironing,” in Formability: Analysis, Modeling and Experimentation, S. S. Hecker, A. K. Ghosh, and H. L. Gegel, eds., TMS-AIME, New York, pp. 78–95.

Leu, D. K. , 1997, “Prediction of the Limiting Drawing Ratio and the Maximum Drawing Load in Cup-Drawing,” Int. J. Mach. Tools Manuf., 37, No. 2, pp. 201–213.

Leu, D. K. , 1999, “The Limiting Drawing Ratio for Plastic Instability of the Cup-Drawing Process,” J. Mater. Process. Technol., 86, pp. 168–176.

Dodd, B., and Atkins, A. G., 1983, “Limiting Drawing Ratios in Sheet Materials According to One of Hill’s New Anisotropic Yield Criteria,” in Developments in the Drawing of Metals, (Conf. Proceedings), The Metal Society London, May, 11–13, pp. 87–89.

Mori, K., and Takuda, H., 1996, “Prediction of Forming Limit in Deep Drawing by Combination of Finite Element Simulation and Criterion for Ductile Fracture,” Transactions of NAMRI/SME, XXIV, pp. 143–148.

Korhonen, A. S. , 1982, “Drawing Force in Deep Drawing of Cylindrical Cup with Flat-Nosed Punch,” ASME J. Eng. Ind., 104, pp. 29–38.

Leu, D. K. , 1997, “Prediction of the Maximum Drawing Load in the Cup-Drawing Process of Sheet Metals,” J. Mater. Process. Technol., 72, pp. 256–261.

Thông tin
Thông tin xuất bản

Journal of Engineering Materials and Technology

Tập 126 Số 1

116-122

Thông tin tác giả