A Dual-Mechanism Approach to the Prediction of Machining Forces, Part 1: Model Development

ASME International - Tập 117 Số 4 - Trang 526-533 - 1995
William J. Endres1, Richard E. DeVor1, Shiv G. Kapoor1
1Department of Mechanical and Industrial Engineering, University of Illinois at Urbana-Champaign, Urbana, IL

Tóm tắt

A cutting-process model addressing the chip removal and edge ploughing mechanisms separately yet simultaneously is presented. The model is developed such that it is readily applicable in an industrial setting, its coefficients have physical meaning, and it can be calibrated with a concise quantity of orthogonal cutting data. The total cutting and thrust forces are each the summation of its individual components acting on the rake face and clearance face. These components are calculated using the rake and effective clearance angles from the normal and friction forces acting on each of these tool surfaces. These normal and friction forces are calculated by the chip removal and edge ploughing portions of the model, respectively, using four empirical coefficients. To calculate the clearance face forces, the interference volume is required, the calculation of which is based on a geometrical representation of the clearance face interference region. This representation is characterized in part by the depth of tool penetration, which is influenced by thermal energy generation and is therefore determined using a fifth empirical model.

Từ khóa


Tài liệu tham khảo

Albrecht P. , 1960, “New Developments in the Theory of the Metal-Cutting Process—Part I. The Ploughing Process in Metal Cutting,” ASME JOURNAL OF ENGINEERING FOR INDUSTRY, Vol. 82, pp. 348–358.

Albrecht P. , 1961, “New Developments in the Theory of the Metal-Cutting Process—Part II. The Theory of Chip Formation,” ASME JOURNAL OF ENGINEERING FOR INDUSTRY, Vol. 83, pp. 557–571.

Cook N. H. , 1959, “Self-Excited Vibrations in Metal Cutting,” ASME JOURNAL OF ENGINEERING FOR INDUSTRY, Vol. 81, pp. 183–186.

Delio, T., Tlusty, J., Smith, S., and Zamudio, C., 1990, “Stiffness, Stability, and Loss of Process Damping in High-Speed Machining,” Proc., ASME Symposium on Fundamental Issues in Machining in Honor of B. F. von Turkovich, PED-Vol. 43, pp. 171–191.

Endres, W. J., 1992, “A Dual Mechanism Approach to the Prediction of Machining Forces in Metal-Cutting Processes,” Ph.D. Thesis, University of Illinois at Urbana-Champaign.

Endres, W. J., Sutherland, J. W., DeVor, R. E., and Kapoor, S. G., 1990, “A Dynamic Model of the Cutting Force System in the Turning Process,” Proc., ASME Symposium on Monitoring and Control for Manufacturing Processes, PED-Vol. 44, pp. 193–212.

Ernst H. , and MerchantM. E., 1941, “Chip Formation, Friction, and High Quality Machined Surfaces,” Trans. ASM, Vol. 29, pp. 299–328.

Kececioglu D. , 1958a, “Shear-Strain Rate in Metal Cutting and its Effects on Shear-Flow Stress,” Transactions of the ASME, Vol. 80, pp. 158–168.

Kececioglu D. , 1958b, “Shear-Zone Temperature in Metal Cutting and its Effects on Shear-Flow Stress,” Transactions of the ASME, Vol. 80, pp. 541–546.

Kececioglu D. , 1960, “Shear-Zone Size, Compressive Stress, and Shear Strain in Metal-Cutting and Their Effects on Mean Shear-Flow Stress,” ASME JOURNAL OF ENGINEERING FOR INDUSTRY, Vol. 82, pp. 79–86.

Kobayashi S. , and ThomsenE. G., 1959, “Some Observations on the Shearing Process in Metal Cutting,” ASME JOURNAL OF ENGINEERING FOR INDUSTRY, Vol. 81, pp. 251–261.

Kobayashi S. , HerzogR. P., EgglestonD. M., and ThomsenE. G., 1960, “A Critical Comparison of Metal-Cutting Theories With New Experimental Data,” ASME JOURNAL OF ENGINEERING FOR INDUSTRY, Vol. 82, pp. 333–347.

Lesieutre, B. C., 1992, “Network and Load Modeling for Power System Dynamic Analysis,” Ph.D. Thesis, University of Illinois at Urbana-Champaign.

Masuko M. , 1953, “Fundamental Researches on the Metal Cutting (1st Report)—A New Analysis of Cutting Force,” Trans. Japanese Society of Mechanical Engineers, Vol. 19, pp. 32–39.

Masuko M. , 1956, “Fundamental Researches on the Metal Cutting (2nd Report)—The Theoretical Equation of the Indentation-Force Acting on a Cutting Edge and its Experimental Discussion,” Trans. Japanese Society of Mechanical Engineers, Vol. 22, pp. 371–377.

Merchant M. E. , 1944, “Basic Mechanics of the Metal-Cutting Process,” ASME Journal of Applied Mechanics, Vol. 66, pp. A-168 to A-175A-168 to A-175.

Nigm M. M. , 1981, “A Method for the Analysis of Machine Tool Chatter,” Int. Journal Machine Tool Design Research, Vol. 21, pp. 251–261.

Nigm M. M. , and SadekM. M., 1977, “Experimental Investigation of the Characteristics of Dynamic Cutting Processes,” ASME JOURNAL OF ENGINEERING FOR INDUSTRY, Vol. 99, pp. 440–418.

Oxley P. L. B. , 1963, “Rate of Strain Effect in Metal Cutting,” ASME JOURNAL OF ENGINEERING FOR INDUSTRY, Vol. 85, pp. 335–338.

Shaw M. C. , and DeSalvoG. J., 1970, “A New Approach to Plasticity and its Application to Blunt Two Dimensional Indenters,” ASME JOURNAL OF ENGINEERING FOR INDUSTRY, Vol. 92, pp. 472–479.

Sisson T. R. , and KeggR. L., 1969, “An Explanation of Low-Speed Chatter Effects,” ASME JOURNAL OF ENGINEERING FOR INDUSTRY, Vol. 91, pp. 951–958.

Sutherland, J. W., 1988, “A Dynamic Model of the Cutting Force System in the End Milling Process,” Proc., ASME Symposium on Sensors and Controls for Manufacturing, PED-Vol. 33, pp. 53–62.

Thomsen E. G. , 1966, “Application of the Mechanics of Plastic Deformation to Metal Cutting,” Annals of C.I.R.P., Vol. 14, pp. 113–123.

Tlusty, J., and Polacek, M., 1963, “The Stability of the Machine Tool Against Self-Excited Vibrations in Machining,” ASME Prod. Engr. Res. Conference, Pittsburgh, pp. 454–465.

Tobias S. A. , and FishwickW., 1958, “The Chatter of Lathe Tools Under Orthogonal Cutting Conditions,” Transactions of the ASME, Vol. 80, pp. 1079–1088.

Wu D. W. , 1988, “Application of a Comprehensive Dynamic Cutting Force Model to Orthogonal Wave Generating Processes,” Int. Journal of Mechanical Sciences, Vol. 30, pp. 1–20.

Wu D. W. , 1989, “A New Approach of Formulating the Transfer Function for Dynamic Cutting Processes,” ASME JOURNAL OF ENGINEERING FOR INDUSTRY, Vol. 111, pp. 37–47.

Thông tin
Thông tin xuất bản

ASME International

Tập 117 Số 4

526-533

Thông tin tác giả