Study the geometric shape-similarity of the projection and the characteristics of the cutting edges of the grains synthetic diamond grinding powders

Waddel, 1932, Volume, shape, and roundness of rock particles, J. Geol., 40, 443 Krumbein, 1941, Measurement and geological significance of shape and roundness of sedimentary particles, J. Sediment. Petrol., 11, 64 Lees, 1964, A new method for determining the angularity of particles, Sedimentology, 3, 2, 10.1111/j.1365-3091.1964.tb00271.x Pentland, 1927 Wentworth, 1933, The shape of rock particle: a discussion, J. Geol., 41, 306 Pye, 1943, Sphericity determination of pebbles and grains, J. Sediment. Petrol., 13, 28 Riley, 1941, Projection sphericity, J. Sediment. Petrol., 11, 94 Aschenbrenner, 1956, A new method of expressing particle sphericity, J. Sediment. Petrol., 26, 15 Sukumaran, 2001, Quantitative characterisation of the geometry of discrete particles, Geotechnique, 51, 619, 10.1680/geot.2001.51.7.619 Cavarretta, 2009, Applying 2D shape analysis techniques to granular materials with 3D particle geometries, AIP Conf. Proc., 1145, 833, 10.1063/1.3180057 . Rodriguez, 2013, Particle shape quantities and measurement techniques review, EJGE, 18, 169 Powers, 1953, A new roundness scale for sedimentary particles, J. Sediment. Res., 23, 117 Rabinowicz, 1995, 336 Hamblin, 1996, Description of abrasive particle shape and its relation to two-body abrasive wear, Tribol. Trans., 39, 803, 10.1080/10402009608983598 Pintaude, 2016, Remarks on the application of two-dimensional shape factors under severe wear conditions, Friction, 4, 65, 10.1007/s40544-016-0105-y De Pellegrin, 2002, Assessing the role of particle shape and scale in abrasion using ‘sharpness analysis’: Part 1. Technique development, Wear, 253, 1016, 10.1016/S0043-1648(02)00232-6 Pintaude, 2011, Characteristics of abrasive particles and their implications on wear, 117 Jankauskas, 2007, Study of wear prediction by applying surface microgeometric parameters, Mechanika, 67, 65 Coseglio, 2009, Abrasive particle characterization following different measurements of shape factor Nikitin, 1992 Yashcheritsyn, 1972 Kuznetsov, 1964, The influence of geometrical parameters of synthetic diamond grains on their cutting properties, Stanki Instrum., 12, 28 Petasyuk, 2010, Interpretative and applied aspects of some morphological characteristics of superabrasive powders, J. Superhard Mater., 32, 128, 10.3103/S1063457610020073 Petasyuk, 2018, A study of the tendency and extent of variation of morphometric characteristics of standard synthetic diamond grits in a continuous series of their grades and sizes, J. Superhard Mater., 40, 414, 10.3103/S1063457618060072 Linke, 2015, A review on properties of abrasive grits and grit selection, Int. J. Abras. Technol., 7, 46, 10.1504/IJAT.2015.070582 1995 2003 List, 2006, A new system for single particle strength testing of grinding powders, Ind. Diam. Rev., 1, 42 Novikov, 2003, Computer-based diagnostic sieve for identification of grit size and grit size distribution in microscopic samples of diamond grits, J. Superhard Mater., 25, 68 Loshak, 2013, Density of diamond crystals for static loading, Metrolohiya ta prylady, 2, 11 Petasyuk, 2016, A system-analogue method of identification of geometric shape of the abrasive grain projection, J. Superhard Mater., 38, 277, 10.3103/S1063457616040092 Petasyuk, 2014, System and criterial method of the identification and quantitative estimation of the geometrical shape of the abrasive powder grains projection, Powder Technol., 264, 78, 10.1016/j.powtec.2014.05.008 Safonova, 2013 Petasyuk, 2008, LrAprox computer software system for multivariant construction and analysis of empirical mathematical models, for the use in theoretical and applied problems of materials science, vol. 31, 58