The effect of track alignment irregularity on wheel-rail contact geometry relationship in a turnout zone
Tóm tắt
The irregularity is a key factor affecting the wheel-rail contact geometry relationship. In this paper, we calculated the wheel-rail contact points at typical sections and obtained the longitudinal variation of the wheel-rail geometry relationship with the trace line method. The profile of the key rail sections was matched by cubic spline curve, and the shape interpolation was realized in non-controlling sections. The results show that the roll angles at each typical section increases gradually with the enlargement of track alignment irregularity. When the flange contact occurs, the roll angle increases dramatically. Proper track alignment irregularity towards the switch rail improves the structure irregularity of the turnout.
Tài liệu tham khảo
J.M. Yan, Z.Z. Yin, B.L. Guo, et al., Experimental study of the wheel-rail contact geometry relationship, Rolling Stock, 1983, 6(1): 54–57 (in Chinese).
B. Chen, C.G. Wang, S.C. Sun, et al., Effect of wheel-rail contact geometric on stability of high-speed passenger car, Railway Locomotive and Car, 2008, 28(1): 189–192 (in Chinese).
Q.M. Bu, L.Q. Yao, Study on the geometric relation of wheel-rail contact, Journal of Suzhou University (Natural Science Edition), 2011, 27(3): 79–84 (in Chinese).
L. Li, D.B. Cui, X.S. Jin, State of arts of research on railway wheel profile optimization, Journal of Southwest Jiaotong University, 2009, 41(1): 13–19 (in Chinese).
X.J. Sun, W.X. Zhou, Tread wear and its effect on wheel-rail contact geometric, Rolling Stock, 2010, 48(7): 1–4 (in Chinese).
P. Wang, R. Chen, R.S. Yang, et al., The Design Theory of Jointless Turnout on Bridge, Chengdu: Southwest Jiaotong University Press, 2011 (in Chinese).
P. Wang, X.Y. Liu, Calculation Theory and Design Method of Jointless Turnout, Chengdu: Southwest Jiaotong University Press, 2007 (in Chinese).
P. Wang, Design Theory and Practice of Turnout in High-Speed Railway, Chengdu: Southwest Jiaotong University Press, 2011 (in Chinese).
Z.S. Ren, S.G. Sun, Study on the wheel-rail contact geometric relation of the turnout zone, Engineering Mechanics, 2008, 25(11): 223–230 (in Chinese).
Y. Cao, P. Wang, W.H. Zhao, Dynamic responses due to irregularity of No. 38 turnout for high-speed railway, In: Proc. of the third ICTE2011, Chengdu, 2011: 2544–2549.
P. Wang, R. Chen, X.P. Chen, Wheel-rail relationship optimization of switch zone in high-speed railway turnout, In: Proc. of 2009 Int. Conf. on International Conference on Transportation Engineering 2009 (ICTE 2009), Chengdu, 2009: 2833–2838.
P. Wang, R. Chen, X.P. Chen, Optimization of dynamic design for ballastless turnout on bridges in high-speed railways, In: Proc. of 2010 ICCTP 2010, Beijing, 2010: 3305–3312.
K.W. Wang, The track of wheel contact points and the calculation of wheel-rail geometric contact parameters, Journal of Southwest Jiaotong University, 1984, 1(1): 89–99 (in Chinese).
W.H. Zhang, The calculation method of wheel-rail contact points in space, China Railway Science, 2006, 27(4): 76–79 (in Chinese).
Z.S. Ren, Study on wheel-rail multi-point contact calculation, Journal of the China Railway Society, 2011, 33(1): 25–30 (in Chinese).
P.T. Ni, K.W. Wang, W.H. Zhang, et al., Calculation method of wheel-rail contact relationship, Journal of Traffic and Transportation Engineering, 2006, 6(4): 10–13 (in Chinese).
P. Xu, C.B. Cai, S.H. Luo, A numerical calculating method for two-point wheel-rail contact, Rolling Stock, 2010, 48(8): 1–5 (in Chinese).
Research Group of High-Speed Turnout, Development report of No. 18 turnout with the speed of 350 km/h in ballastless track, Chengdu: MOE Key Laboratory of High-Speed Railway Engineering, 2007 (in Chinese).
S.X. Quan, P. Wang, H.Y. Zhang, The analysis of the influencing factors of rail lateral shift on curve, Railway Engineering, 2010, 2(1): 114–116 (in Chinese).
S.X. Quan, X.K. Wei, P. Wang, Explore and analyse the control methods of lateral and vertical profile irregularities of ballastless track, Railway Standard Design, 2012, 2(1): 11–15 (in Chinese).
Z. Wu, S.X. Quan, X.Y. Liu, Vertical dynamic calculation analysis of elastic bolster in ballastless track, Chinese Railways, 2008, 9(1): 35–39 (in Chinese).
Y. Cao, P. Wang, Design on plane linearity of turnouts as well as researches and applications of drafting system, Railway Standard Design, 2010(11): 23–26 (in Chinese).
Y. Cao, P. Wang, W.H. Zhao, Study on turnout line-shape design based on plane parameters method, Railway Engineering, 2011, 2(1): 101–103 (in Chinese).