Through-thickness texture in clock-rolled tantalum plate

Cardonne, 1995, Tantalum and its alloys, Int J Refract Met Hard Mater, 13, 187, 10.1016/0263-4368(95)94023-R Hupalo, 2001, The annealing behavior of oligocrystalline tantalum deformed by cold swaging, Mater Sci Eng A, 318, 216, 10.1016/S0921-5093(01)01323-5 Clark, 1991, Effect of processing variables on texture and texture gradients in tantalum, Metall Trans A, 22, 2039, 10.1007/BF02669871 Chen, 2011, Comparison of texture evolution between different thickness layers in cold rolled Al–Mg alloy, Mater Charact, 62, 1188, 10.1016/j.matchar.2011.10.007 Engler, 2000, A study of through-thickness texture gradients in rolled sheets, Metall Mat Trans A, 31, 2299, 10.1007/s11661-000-0146-7 Huh, 1999, Evolution of through-thickness texture gradients in various steel sheets, Met Mater, 5, 437, 10.1007/BF03026156 Michaluk, 2002, Correlating discrete orientation and grain size to the sputter deposition properties of tantalum, J Elec Materi, 31, 2, 10.1007/s11664-002-0165-9 Sarkar, 2010 Vandermeer, 1977, Deformation zone geometry and texture gradients in cold rolled niobium, Texture Cryst Solids, 2, 183, 10.1155/TSM.2.183 Mathaudhu, 2007, Processing microstructure property relationships in severely deformed tantalum, Mater Sci Eng A, 463, 94, 10.1016/j.msea.2006.08.120 Hosseini, 2009, Dislocation structure and strength evolution of heavily deformed tantalum, Int J Refract Met Hard Mater, 27, 605, 10.1016/j.ijrmhm.2008.09.006 Clark, 1992, Influence of transverse rolling on the microstructural and texture development in pure tantalum, Metall Trans A, 23, 2183, 10.1007/BF02646011 Suwas, 2003, Role of strain path change in texture development, Mater Sci Eng A, 356, 368, 10.1016/S0921-5093(03)00149-7 Zhang, 2013, A comparative study of clock rolling and unidirectional rolling on deformation/recrystallization microstructure and texture of high purity tantalum plates, Int J Refract Met Hard Mater, 41, 453, 10.1016/j.ijrmhm.2013.06.003 Deng, 2014, Texture evolution of high purity tantalum under different rolling paths, J Mater Process Technol, 214, 462, 10.1016/j.jmatprotec.2013.09.026 Mishin, 2000, Through-thickness texture gradients in cold-rolled aluminum, Metall Mater Trans A, 31, 1653, 10.1007/s11661-000-0175-2 Michaluk, 2002, Quantifying the recrystallization texture of tantalum, JOM, 54, 51, 10.1007/BF02822623 Čapková, 1984, The surface roughness effect in texture measurements by the Schulz X‐ray reflection method, Phys Status Solidi A, 81, K113, 10.1002/pssa.2210810245 Pawlik, 1986, Determination of the orientation distribution function from pole figures in arbitrarily defined cells, Phys Status Solidi B, 134, 477, 10.1002/pssb.2221340205 Davies, 2008, Introduction to texture analysis, 1 Huh, 1995, On the influence of cross-rolling on shear band formation and texture evolution in low carbon steel sheets, Texture Microst, 24, 225, 10.1155/TSM.24.225 Vandermeer, 1979, Recovery and recrystallization in rolled tantalum single crystals, Metall Trans A, 10, 1031, 10.1007/BF02811649 Dillamore, 1965, Preferred orientation in wrought and annealed metals, Metall Rev, 10, 271, 10.1179/095066065790138348 Raabe, 1995, Simulation of rolling textures of bcc metals considering grain interactions and crystallographic slip on {110}, {112} and {123} planes, Mater Sci Eng A, 197, 31, 10.1016/0921-5093(94)09770-4 Clark, 1991, Influence of initial ingot breakdown on the microstructural and textural development of high-purity tantalum, Metall Trans A, 22, 2959, 10.1007/BF02650255 Huh, 2005, Effect of through-thickness macro and micro-texture gradients on ridging of 17% Cr ferritic stainless steel sheet, Steel Res Int, 76, 797, 10.1002/srin.200506098 Raabe, 1993, Textures of ferritic stainless steels, Mater Sci Technol, 9, 302, 10.1179/mst.1993.9.4.302 Raabe, 1995, On the orientation dependence of static recovery in low-carbon steels, Scr Metall Mater, 33, 735, 10.1016/0956-716X(95)00276-2 Huh, 1998, Effect of lubrication on the evolution of microstructure and texture during rolling and recrystallization of copper, Mater Sci Eng A, 247, 152, 10.1016/S0921-5093(97)00772-7 Bhattacharjee, 2013, The effect of starting grain size on the evolution of microstructure and texture in nickel during processing by cross-rolling, Mater Charact, 76, 21, 10.1016/j.matchar.2012.11.005 Hughes, 1997, High angle boundaries formed by grain subdivision mechanisms, Acta Mater, 45, 3871, 10.1016/S1359-6454(97)00027-X Sandim, 1999, Grain subdivision and recrystallization in oligocrystalline tantalum during cold swaging and subsequent annealing, Int J Refract Met Hard Mater, 17, 431, 10.1016/S0263-4368(99)00035-9 Hansen, 2001, New discoveries in deformed metals, Metall Mater Trans A, 32, 2917, 10.1007/s11661-001-0167-x