Experimental study of microstructure changes due to low cycle fatigue of a steel nanocrystallised by Surface Mechanical Attrition Treatment (SMAT)
Tài liệu tham khảo
Lu, 1999, Surface nanocrystallization (SNC) of metallic materials – presentation of the concept behind a new approach, J. Mater. Sci. Technol., 15, 193
Lu, 2004, Nanostructured surface layer on metallic materials induced by surface mechanical attrition treatment, Mater. Sci. Eng. A, 375–377, 38, 10.1016/j.msea.2003.10.261
Roland, 2007, Enhanced mechanical behavior of a nanocrystallised stainless steel and its thermal stability, Mater. Sci. Eng. A, 445–446, 281, 10.1016/j.msea.2006.09.041
Uusitalo, 2009, Fatigue properties of steels with ultrasonic attrition treated surface layers, Mater. Sci. Forum, 604–605, 239, 10.4028/www.scientific.net/MSF.604-605.239
Roland, 2006, Fatigue life improvement through surface nanostructuring of stainless steel by means of surface mechanical attrition treatment, Scr. Mater., 54, 1949, 10.1016/j.scriptamat.2006.01.049
Tian, 2007, A study of the effect of nanostructured surface layers on the fatigue behaviors of a C-2000 superalloy, Mater. Sci. Eng. A, 468–470, 164, 10.1016/j.msea.2006.10.150
Dai, 2008, Analysis of fatigue resistance improvements via surface severe plastic deformation, Int. J. Fatigue, 30, 1398, 10.1016/j.ijfatigue.2007.10.010
Shaw, 2010, A direct comparison in the fatigue resistance enhanced by surface severe plastic deformation and shot peening in a C-2000 superalloy, Mater. Sci. Eng. A, 527, 986, 10.1016/j.msea.2009.10.028
Kumar, 2012, Effect of surface mechanical attrition treatment on fatigue lives of alloy 718, Trans. Indian Inst. Metals, 65, 473, 10.1007/s12666-012-0154-5
Micoulaut, 2007, Granular gases in mechanical engineering on the origin of heterogeneous ultrasonic shot peening, Granul. Matter, 9, 25, 10.1007/s10035-006-0018-y
Ruan, 2010, Characterization of plastically graded nanostructured material: part II. The experimental validation in surface nanostructured material, Mech. Mater., 42, 698, 10.1016/j.mechmat.2010.04.007
Blonde, 2010, Evolution of texture and microstructure in pulsed electrodeposited Cu treated by surface mechanical attrition treatment, J. Alloys Compd., 504, S410, 10.1016/j.jallcom.2010.04.040
Zhang, 2011, A computational study of plastic deformation in AISI 304 induced by surface mechanical attrition treatment, Mech. Adv. Mater. Struct., 18, 572, 10.1080/15376494.2011.621828
Liu, 2000, Surface nanocrystallization of 316L stainless steel induced by ultrasonic shot peening, Mater. Sci. Eng. A, 286, 91, 10.1016/S0921-5093(00)00686-9
Samih, 2013, In-depth quantitative analysis of the microstructures produced by surface mechanical attrition treatment (SMAT), Mater. Charact., 83, 129, 10.1016/j.matchar.2013.06.006
Oddershede, 2015, Deformation-induced orientation spread in individual bulk grains of an interstitial-free steel, Acta Mater., 85, 301, 10.1016/j.actamat.2014.11.038
Wei, 2004, Grain-boundary sliding and separation in polycrystalline metals: application to nanocrystalline fcc metals, J. Mech. Phys. Solids, 52, 2587, 10.1016/j.jmps.2004.04.006
Wei, 2008, Enhanced strain-rate sensitivity in fcc nanocrystals due to grain-boundary diffusion and sliding, Acta Mater., 56, 1741, 10.1016/j.actamat.2007.12.028
Meyers, 2006, Mechanical properties of nanocrystalline materials, Prog. Mater. Sci., 51, 427, 10.1016/j.pmatsci.2005.08.003