Optimizing the simultaneous cutting-edge angles, included angle and nose radius for low cutting force in turning polyamide PA66

Dusunceli, 2008, The effects of manufacturing techniques on viscoelastic and viscoplastic behavior of high density polyethylene (HDPE), Mater. Des., 29, 1117, 10.1016/j.matdes.2007.06.003 Chabbi, 2017, Predictive modeling and multi-response optimization of technological parameters in turning of Polyoxymethylene polymer (POM C) using RSM and desirability function, Measurement, 95, 99, 10.1016/j.measurement.2016.09.043 Mata, 2006, Physical cutting model of polyamide composites (PA66 GF30), Mater. Sci. Forum, 514, 643, 10.4028/www.scientific.net/MSF.514-516.643 Deopura, 2008 Pan, 2019, 2 Pan, 2017, Triboelectric effect: a new perspective on electron transfer process, J. Appl. Phys., 122, 10.1063/1.5006634 kumar, 2009, Effect of particulate fillers on mechanical and abrasive wear behavior of polyamide 66/polypropylene nanocomosites, Mater. Des., 3852, 10.1016/j.matdes.2009.01.034 Sakai, 2007, Study on Permeation Behavior and Chemical Degradation of PA66 in Acid Solution, Polym. Degrad. Stabil., 379 Kobayashi, 2006, Ultra precision machining of plastics. part 1. Polymethyl methacrylate, Polym. Plast. Technol. Eng., 22, 15, 10.1080/03602558408070029 Cheung, 1999, A theoretical and experimental investigation of surface roughness formation in ultra-precision diamond turning, Int. J. Mach. Tool Manufact., 40, 979, 10.1016/S0890-6955(99)00103-0 Vaxevanidis, 2010, Surface roughness analysis in high speed-dry turning of a tool steel, 551 Gaitonde, 2009, Study on some aspects of machinability in unreinforced and reinforced polyamides, J. Compos. Mater., 43, 725, 10.1177/0021998309101298 Marin, 2010, 9, 3 Tamizharasan, 2012, Optimization of cutting inserts geometry using DEFORM-3D: numerical simulation and experimental validation, Int. J. Simulat. Model., 11, 65, 10.2507/IJSIMM11(2)1.200 Tamizharasan, 2012, Analysis of surface roughness and material removal rate in turning using taguchi's technique Taha, 2010, Insert geometry effects on surface roughness in turning process of AISI D2 steel, J. Zhejiang Univ. - Sci., 11, 966, 10.1631/jzus.A1001356 Senthilkumar, 2014, Effect of tool geometry in turning AISI 1045 steel: experimental investigation and FEM analysis, Arabian J. Sci. Eng., 39, 4963, 10.1007/s13369-014-1054-2 Islam, 2015, Effects of insert geometry and feed rate on quality characteristics of turned parts, J. Adv. Manuf. Syst., 14, 149, 10.1142/S0219686715500109 Abdalrahman, 2019, The influence of cutting-edge angles included angle and nose radius on surface finish of aluminum alloy 1050 in turning, ZANCO Journal of Pure and Applied Sciences The official scientific journal of Salahaddin University-Erbil, 32, 31 Kovač, 2012, A review of artificial intelligence approaches applied in inteligent processes, Jornal of Production Engineeing, 15, 1