Relationship between tool flank wear area and component forces in single point turning

Jawahir, 1995, A new parametric approach for the assessment of comprehensive tool wear in coated grooved tools, Ann. CIRP, 44, 49, 10.1016/S0007-8506(07)62273-2 Giusti, 1987, On line sensing of flank and crater wear of cutting tools, Ann. CIRP, 36, 41, 10.1016/S0007-8506(07)62549-9 Andreasen, 1993, Automatic chip breakage detection in turning by frequency analysis of cutting force, Ann. CIRP, 42, 45, 10.1016/S0007-8506(07)62388-9 Nair, 1992, Turning process identification through force transients, Trans. ASME, J. Eng. Ind., 114, 1, 10.1115/1.2899754 Wu, 1988, Comprehensive dynamic cutting force model and its application to wave removing processes, Trans. ASME, J. Eng. Ind., 110, 153, 10.1115/1.3187864 Danai, 1987, A dynamic state model for on-line tool wear estimation in turning, Trans. ASME, J. Eng. Ind., 109, 396, 10.1115/1.3187145 Zhou, 1995, A system for monitoring cutting tool spontaneous failure based on stress estimation, J. Mater. Process. Technol., 48, 231, 10.1016/0924-0136(94)01654-J Elanayar, 1996, Modeling of tool forces for worn tools: flank wear effects, J. Manuf. Sci. Technol., 118, 24 K.F. Martin, J.A. Brandon, R.I. Grosvenor, A. Owen, A comparison of in-process tool wear measurement methods in turning, in: Proceedings of the International Machine Tool Design and Research Conference, 1986, Macmillan, Basingstoke, UK, pp. 289–296. P.M. Lister, G. Barrow, Tool condition monitoring systems, in: Proceedings of the International Machine Tool Design and Research Conference, 1986, Macmillan, Basingstoke, UK, pp. 271–288. A.S. Jhita, V.K. Jain, On the tool wear during face turning, in: Proceedings of the International Machine Tool Design and Research Conference, 1981, Macmillan, Basingstoke, UK, pp. 247–253. R. Mackinnon, G.E. Wilson, A.J. Wilkinson, Tool condition monitoring using multicomponent force measurements, in: Proceedings of the International Machine Tool Design and Research Conference, 1986, Macmillan, Basingstoke, UK, pp. 317–324. Lim, 1995, Tool wear monitoring in machine turning, J. Mater. Process. Technol., 51, 25, 10.1016/0924-0136(94)01354-4 Lin, 1995, A study of cutting with a CBN tool, J. Mater. Process. Technol., 49, 149, 10.1016/0924-0136(94)01321-Q Du, 1994, A study on the modeling of tool motion and high-accuracy surface generation by the use of cutting-force signals, J. Mater. Process. Technol., 47, 101 Sampath, 1984, Tool fracture probability under steady state cutting conditions, Trans. ASME, J. Eng. Ind., 106, 161, 10.1115/1.3185927 Sampath, 1984, Tool fracture probability of cutting tools under different existing conditions, Trans. ASME, J. Eng. Ind., 106, 168, 10.1115/1.3185927 R. Milovic, M.L.H. Wise, Tool wear in the machining of leaded free-cutting steel, in: Proceedings of the International Machine Tool Design and Research Conference, 1985, Macmillan, Basingstoke, UK, pp. 287–293. Looney, 1992, The turning of an Al/SiC metal–matrix composite, J. Mater. Process. Technol., 33, 453, 10.1016/0924-0136(92)90279-2 G. Boothroyed, Fundamentals of Machining and Machine Tools, Second Edition, Marcel Dekker, New York, 1989. Ravindra, 1993, Modeling of tool wear based on cutting forces in turning, Wear, 169, 25, 10.1016/0043-1648(93)90387-2 Oraby, 1991, Developments of models for tool wear force relationships in metal cutting, Int. J. Mech. Sci., 33, 125, 10.1016/0020-7403(91)90062-8 Barata, 1991, Monitoring the wear of sintered high-speed steel tools, J. Mater. Process. Technol., 25, 195, 10.1016/0924-0136(91)90089-W Lee, 1986, Effects of tool fracture on machining force dynamics, J. Mech. Work. Technol., 17, 205, 10.1016/0378-3804(88)90022-8