On the size effect in abrasive and erosive wear

Rabinowicz, 1961, A study of abrasive wear under threebody condition, Wear, 4, 345, 10.1016/0043-1648(61)90002-3 Finnie, 1960, Erosion of surfaces by solid particles, Wear, 3, 87, 10.1016/0043-1648(60)90055-7 Tilly, 1973, A two stage mechanism of ductile erosion, Wear, 23, 87, 10.1016/0043-1648(73)90044-6 Malkin, 1972, Size effect in abrasive process, 291 Malkin, 1975, Minimum energy in abrasive process, Wear, 32, 15, 10.1016/0043-1648(75)90201-X Graham, 1972, An investigation into the mode of metal removal in the grinding process, Wear, 19, 301, 10.1016/0043-1648(72)90122-6 Armarego, 1962, On the size effect in metal cutting, Int. J. Prod. Res., 1, 75, 10.1080/00207546108943090 Larsen-Badse, 1972, Effect of strain-rate sensitivity on scale phenomena in chip formation, 209 Rabinowicz, 1965, Effect of abrasive particle size on wear, Wear, 8, 381, 10.1016/0043-1648(65)90169-9 Larsen-Badse, 1968, Influence of grit size on groove formation during sliding abrasion, Wear, 11, 213, 10.1016/0043-1648(68)90559-0 Larsen-Badse, 1968, Influence of grit diameter and specimen size on wear during sliding abrasion, Wear, 12, 35, 10.1016/0043-1648(68)90574-7 Goddard, 1962, A theory of friction and wear during the abrasion of metals, Wear, 5, 114, 10.1016/0043-1648(62)90235-1 Avient, 1960, An experimental study of friction and wear during abrasion, 258, 159 Larsen-Badse, 1964, Some effects of specimen size on abrasive wear, Wear, 19, 27, 10.1016/0043-1648(72)90439-5 Moore, 1976, Plastic deformation below worn surface, Metall. Trans. A, 7, 1833, 10.1007/BF02654978 Tilly, 1970, The interaction of particle and material behavior in erosion processes, Wear, 16, 447, 10.1016/0043-1648(70)90171-7 Date, 1976, Effect of grit size on abrasion with coated abrasives, Wear, 40, 223, 10.1016/0043-1648(76)90100-9 Rabinowicz, 1964, Practical uses of the surface energy criterion, Wear, 7, 9, 10.1016/0043-1648(64)90074-2 Sheldon, 1966, On the brittle behavior of nominally brittle materials during erosive cutting, J Eng. Ind., 88, 387, 10.1115/1.3672666 Shaw, 1972, A new theory of grinding, Mech. Chem. Eng. Trans., 8, 73 Phadke, 1975, Evaluation of coated abrasive grain geometry and wear via continuous time series models, Wear, 31, 29, 10.1016/0043-1648(75)90120-9 van Groenou, 1977, The high speed size effect in grinding: the role of heat generation, Wear, 44, 203, 10.1016/0043-1648(77)90139-9 Hutchings, 1977, Strain rate effects in microparticle impact, J. Phys., 10, 179 Larsen-Badse, 1977, Strain rate effect in low speed two-body abrasion Sin, 1979, Abrasive wear mechanisms and the grit size effect, Wear, 55, 163, 10.1016/0043-1648(79)90188-1 Backer, 1952, The size effect in metal cutting, Trans. Am. Soc. Mech. Eng., 74, 61 Von Turkovich, 1970, Shear stress in metalcutting, J. Eng. Ind., 92, 151, 10.1115/1.3427700 Gane, 1970, The microhardness of metals at very low loads, Philos. Mag., 22, 881, 10.1080/14786437008221059 Kramer, 1961, The effect of surface removal on the plastic behavior of aluminum single crystals, Trans. AIME, 221, 780 Sumino, 1961, Preferential plastic deformation in the surface region of Al and α-Fe single crystals, J. Phys. Soc. Jpn., 16, 131, 10.1143/JPSJ.16.131 Kitajama, 1969, Dislocation distribution near the surface ofweakly deformed copper crystal, Trans. Jpn. Inst. Met., 10, 12, 10.2320/matertrans1960.10.12 Kramer, 1973, Metallographic study of the surface layer, Acta Metall., 21, 695, 10.1016/0001-6160(73)90079-5 Kramer, 1963, The effect of surface removal on the plastic flow characteristics of metals, Trans. AIME, 227, 1003 Fourie, 1967, Plastic deformation of thin copper single crystals, Philos. Mag., 15, 187, 10.1080/14786436708230357 Fourie, 1967, The plastic deformation of thin copper single crystals, Can. J. Phys., 45, 777, 10.1139/p67-059 Fourie, 1968, The flow stress gradient between the surface and center of deformed copper single crystals, Philos. Mag., 17, 735, 10.1080/14786436808223026 Mughrabi, 1970, Investigations of plastically deformed copper single-crystals in the stressapplied state, Phys. Status Solidi, 39, 317, 10.1002/pssb.19700390133 Swann, 1966, The dislocation distribution near the surface of deformed copper, Acta Metall., 14, 900, 10.1016/0001-6160(66)90013-7 Essman, 1968, Die Versetzungsanordnung in Plastisch Verformten Kupfervielkristallen, Acta Metall, 16, 1275, 10.1016/0001-6160(68)90008-4 1977 Larsen-Badse, 1969, Influence of structure on the abrasion resistance of a 1040 steel, Wear, 14, 199, 10.1016/0043-1648(69)90041-6 Moore, 1976, Plastic deformation below worn surface, Metall, Trans. A, 7, 1833, 10.1007/BF02659813 Nakada, 1964, Effects of surface conditions on the stress-strain curves of aluminum and gold single crystals, Trans. AIME, 230, 1339 Marsh, 1963, Fracture of Solids, 119 Fisher, 1952, Discussion on creep behavior of zinc modified by copper in the surface layer, Trans. AIME, 194, 52 Warzala, 1966, Environment sensitive mechanical behavior