Runout effects in milling: Surface finish, surface location error, and stability

Kline, 1983, The effect of runout on cutting geometry and forces in end milling, International Journal of Machine Tool Design and Research, 23, 123, 10.1016/0020-7357(83)90012-4 Lazoglu, 2003, Sculpture surface machining: a generalized model of ball-end milling force system, International Journal of Machine Tools and Manufacture, 43, 453, 10.1016/S0890-6955(02)00302-4 Feng, 1994, The prediction of cutting forces in the ball-end milling process—I. Model formulation and model building procedure,, International Journal of Machine Tools and Manufacture, 34/5, 697, 10.1016/0890-6955(94)90052-3 Feng, 1994, The prediction of cutting forces in the ball-end milling process—II. Cut geometry analysis and model verification, International Journal of Machine Tools and Manufacture, 34, 711, 10.1016/0890-6955(94)90053-1 Zheng, 1999, Theoretical modeling and simulation of cutting forces in face milling with cutter runout, International Journal of Machine Tools and Manufacture, 39, 2003, 10.1016/S0890-6955(99)00023-1 Baek, 1997, A dynamic surface roughness model for face milling, Precision Engineering, 20, 171, 10.1016/S0141-6359(97)00043-3 Atabey, 2003, Mechanics of boring processes—Part II. Multi-insert boring heads, International Journal of Machine Tools and Manufacture, 43, 477, 10.1016/S0890-6955(02)00277-8 Mezentsev, 2002, Use of radial forces for fault detection in tapping, International Journal of Machine Tools and Manufacture, 42, 479, 10.1016/S0890-6955(01)00139-0 Altintas, 1992, In-process detection and suppression of chatter in milling, International Journal of Machine Tools and Manufacture, 32, 329, 10.1016/0890-6955(92)90006-3 Wang, 2003, Identification of cutter offset in end milling without a prior knowledge of cutting coefficients, International Journal of Machine Tools and Manufacture, 43, 687, 10.1016/S0890-6955(03)00028-2 Ko, 2002, Development of a virtual machining system, Part 1: approximation of the size effect for cutting force prediction, International Journal of Machine Tools and Manufacture, 42, 1595, 10.1016/S0890-6955(02)00137-2 Yun, 2001, Accurate 3-D cutting force prediction using cutting condition independent coefficients in end milling, International Journal of Machine Tools and Manufacture, 41, 463, 10.1016/S0890-6955(00)00097-3 Hekman, 1997, In-process monitoring of end milling cutter runout, Mechatronics, 7, 1, 10.1016/S0957-4158(96)00038-4 Yan, 1995, A multi-sensor strategy for tool failure detection in milling, International Journal of Machine Tools and Manufacture, 35, 383, 10.1016/0890-6955(94)E0021-A Stevens, 1995, Runout rejection in end milling through two-dimensional repetitive force control, Mechatronics, 5, 1, 10.1016/0957-4158(94)00043-Q Liang, 1994, Milling force convolution modeling for identification of cutter axis offset, International Journal of Machine Tools and Manufacture, 34, 1177, 10.1016/0890-6955(94)90021-3 Baek, 2001, Optimization of feedrate in a face milling operation using a surface roughness model, International Journal of Machine Tools and Manufacture, 41, 451, 10.1016/S0890-6955(00)00039-0 Smith, 1991, An overview of modeling and simulation of the milling process, Transactions of the ASME: Journal of Engineering for Industry, 113, 169, 10.1115/1.2899674 Ikua, 2001, Prediction of cutting forces and machining error in ball end milling of curved surfaces–I, Theoretical Analysis. Precision Engineering, 25, 266, 10.1016/S0141-6359(01)00077-0 Ranganath, 1999, The role of flank face interference in improving the accuracy of dynamic force predictions in peripheral milling, Transactions of the ASME: Journal of Manufacturing Science and Engineering, 121, 593, 10.1115/1.2833071 Campomanes, 2003, An improved time domain simulation for dynamic milling at small radial immersions, Transactions of the ASME: Journal of Manufacturing Science and Engineering, 125, 416, 10.1115/1.1580852 X. Lui, M. Jun, R. DeVor, S. Kapoor, Cutting mechanisms and their influence on dynamic forces, vibrations and stability in micro-endmilling, in: Proceedings of the 2004 International Mechanical Engineering Congress and Exposition, November 13–20, Anaheim, CA; IMECE2004-62416. W.-M. Chau, Accuracy of milling operations based on dynamic models and simulation. M.S. Thesis, University of Florida, 1992. Altintas, 2000 Tlusty, 1999 Equipment manufacturers are specified for completeness. This does not imply endorsement by the authors. W. Nakkiew, C.W. Lin, J.F., A new method to measure runout of motorized end-milling spindles at very high speed rotations, in: Proceedings of the 18th Annual American Society for Precision Engineering 2003; October 26–31; Portland, OR (on CD). D.N. Dilley, Accuracy, vibration, and stability in drilling and reaming, D.Sc. Dissertation, Washington University in St. Louis, 2003. ASME B46.1-2002. Surface Texture, Surface Roughness, Waviness, and Lay, American Society of Mechanical Engineers, New York 2003. Altintas, 1995, Analytical prediction of stability lobes in milling, Annals of the CIRP, 44, 357, 10.1016/S0007-8506(07)62342-7 Davies, 2002, Stability prediction for low radial immersion milling, Transactions of the ASME: Journal of Manufacturing Science and Engineering, 124, 217, 10.1115/1.1455030 Budak, 2003, An analytical design method for milling cutters with nonconstant pitch to increase stability, Part 1: theory, Part 2: application, Transactions of the ASME: Journal of Manufacturing Science and Engineering, 123, 29, 10.1115/1.1536655 Paris, 2004, Surface shape prediction in high speed milling, International Journal of Machine Tools and Manufacture, 44, 1567, 10.1016/j.ijmachtools.2004.06.005